Cino F400, F600, F700, L600, L700 63

Programming Manual

FuzzyScan

Appendix

Operation Mode Quick Set

Low Power (Low power trigger)

Force (Continued power on)

Alternative (Periodic power off)

Trigger (External triggering)

Toggle (Repeat reading)

Flash (Pulse driven reading)

Presentation (Auto sensing)

Diagnostic (Test reading)

Level (Auto power off)

Contents

Page Description Enable Serial Response Time-out Presentation Control Page Warranty Regulatory LED Eye Safety Laser Eye Safety Getting Started Configure Your FuzzyScan Appendix Page Universal Holder Hand-freeSmartStand desired position for optimized scanning Please note that the SmartStand is not applicable for F400 Series imager System Command Family Code Option Code Programming Procedures Conventions of Programming Menu Program & End System List, Group & Master Default System List, Gro Single scan selection Multiple scans selection Cycling scan selection Dual level selection Parameter Selection ♦ User Defined Symbol ID ♦ ♦ Symbology ID Transmission ♦ Family Code Selection P.C Option Code ♦ Readable Bar Code Setting ♦ Readable Symbology Setting ♦ Code 39/Code 32 Setting ♦ Disable Code Enable Code 39 Select Standard Code 39 as primary format Select Full ASCII Code 39 as primary format ♦ Code 39 Setting ♦ ♦ Codabar/NW-7Setting ♦ Codabar Setting Disable Codabar Enable Codabar Select Codabar standard format Page ♦ UPC-A& UPC-ESetting ♦ UPC Family Setting Disable UPC-A Enable UPC-A Disable UPC-E Page ♦ EAN Setting, EAN Supplement Setting ♦ ♦ EAN Security Level Setting ♦ ♦ UCC Coupon Extended Code Setting ♦ P.CParameter Selection ♦ IATA & Interleaved 2 of 5 Setting ♦ ♦ Code 25 Family Setting ♦ Disable Standard/Industrial 2 of 5 Enable Standard/Industrial 2 of Disable Matrix 2 of 5 Enable Matrix 2 of ♦ Code 11 & Code 93 Setting ♦ Disable Code 11 Enable Code Select 1-checkdigit verification Select 2-checkdigit verification ♦ MSI/Plessey Setting ♦ Disable MSI/Plessy Enable MSI/Plessy Select MOD 10 check digit Select MOD 10-10check digit ♦ Code 128 & UCC/EAN 128 Setting ♦ Disable Code 128 and GS1-128 Enable Code 128 and GS1-128 Disable function code conversion Enable function code conversion ♦ UK/Plessey Setting ♦ Disable UK/Plessey Enable UK/Plessey Select UK/Plessey Standard Format Select UK/Plessey CLSI Format ♦ Telepen Setting ♦ Disable Telepen Enable Telepen Select Telepen Numeric mode Select Telepen Full ASCII mode ♦ GS1 DataBar Setting ♦ Disable GS1 DataBar (RSS-14) Enable GS1 DataBar (RSS-14) Disable GS1 DataBar Limited Enable GS1 DataBar Limited ♦ Linear-stacked& Korea Post Code Setting ♦ ♦ Keyboard Layout (Language) Setting ♦ Keyboard Layout USA (QWERTY) France (AZERTY) Germany (QWERTZ) ♦ Record Suffix, Preamble, Postamble & Caps Lock ♦ Caps Lock Control ♦ Delay Setting ♦ 1-99(x5) msec Intercharacter Delay Interfunction Delay ♦ Emulation Setting & Upper/Lower Case Setting ♦ ♦ Record Suffix, Preamble ,Postamble Setting ♦ STX/ETX Control Disable STX/ETX transmission Enable STX/ETX transmission data frame transmitted via serial interface Page ♦ Protocol, ACK/NAK Setting ♦ Handshaking Protocol None (free running mode) RTS/CTS (hardware handshaking) ACK/NAK (software handshaking) ♦Time Out Setting, Baud Rate, Data Frame ♦ 3 seconds 200 mseconds 4 seconds 500 mseconds ♦ Code 39/Code 128 Emulation ♦ Disable standard Code 39 emulation Enable standard Code 39 skip emulation Enable standard Code 39 replace emulation Enable Full ASCII Code 39 emulation ♦ Operation Mode Setting ♦ Operation Mode Low Power mode Force mode Trigger mode ♦ Buzzer, Indicator, Vibrator, Inverse Reading ♦ Good Read Indicator ♦ Dollar Sign, Redundancy, Scan Rate Control♦ Dollar Sign Control Dollar sign output as “ $ “ Dollar sign output as “ “ Dollar sign output as “ € “ ♦ Flash Duty Cycle, Delay Setting ♦ ♦ Time-outSetting, Good Read Duration ♦ ♦ Presentation Scanning Setting , Trigger Control♦ Presentation Auto-sense Trigger Control ♦ Laser Aiming Control♦ Laser Aiming Control ♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦ Enable 2 digits data length transmission If data length exceeds 99, 3-digitdata length will be transmitted Enable prefix symbology ID transmission Enable suffix symbology ID transmission ♦ Data Formatter Setting ♦ Formatter Control Select one bar code symbology Select all bar code symbologies 1st Insertion ♦ Data Verifier Setting ♦ 2nd Option Code Verifier Control Identified Data Length Determine the identified data length for verification ♦ Data Replacer Setting ♦ Replacer Control 2-digitsidentified position; 1 replacement character ♦ Data Organizer Setting ♦ 2nd Option Code Organizer Control 0 (Forward) 2-digitsidentified position; Select a Bar Code Symbology Position Calculation Application Example Programming Procedure Each AIM Code Identifier contains the three-characterstring ]cm where: ]cm ]= Flag Character c = Code Character m = Modifier Character Reserved ASCII 0 – Enable HEX HEX/ASCII Table Example: PREAMBLE Hex/ASCII Table Page Page FIN (Finish) END (Exit) PROGRAM System Information List (Enter Programming Mode) (SYSLIST) Save User Default

Cino manual 63

Models: F400 F600 F700 L600 L700