Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems manual Product Numbers PA-FE-TX= and PA-FE-FX=, Corporate Headquarters

Models: PA-FE-FX PA-FE-TX

1 64

Download 64 pages 54.09 Kb

Page 1

Product Numbers: PA-FE-TX(=) and PA-FE-FX(=)

PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration

Product Numbers: PA-FE-TX(=) and PA-FE-FX(=)

Platforms Supported: Cisco 7200 Series, Cisco 7000 Series and Cisco 7500 Series with VIP2, Cisco uBR7200 Series, Cisco 7100 Series

Note If you ordered this port adapter as a spare, for your convenience Cisco has included a port adapter installation and conﬁguration note for the Catalyst 5000 series Route Switch Module/Versatile Interface Processor 2 (RSM/VIP2). Your port adapter is fully compatible with the RSM/VIP2.

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive San Jose, CA 95134-1706

USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 526-4100

Text Part Number: 78-2659-08

Image 1

Cisco Systems manual Product Numbers PA-FE-TX= and PA-FE-FX=, Corporate Headquarters

Contents

Corporate Headquarters Product Numbers PA-FE-TX= and PA-FE-FX=Copyright 1996-1999 Cisco Systems, Inc All rights reserved Objectives PrefaceRelated Documentation OrganizationCisco 7200 series router Cisco Documentation CD-ROM Cisco Connection OnlinePort Adapter Overview OverviewC H A P T E R Port Adapter Locations on the Supported Platforms H10447 daughterH6422 Port adapter slotH11323 Receptacles, Cables, and Pinouts LEDsReceive Data + RxD+ RJ-45 connectorTransmit Data + TxD+ Hub or repeater 3 TxD+ 6 TxD Hub or repeater 3 TxD+ 6 TxD 1 RxD+ 2 RxD1 RxD+ 2 RxDJackscrew Pin 1 Any pins not indicated are not used2 TxCLK and RxCLK are generated by the external transceiver Fast Ethernet Overview IEEE 802.3u 100BaseT Specifications IEEE 802.3u 100BaseT SpeciﬁcationsIEEE 802.3u Physical Characteristics Speciﬁcations and Connection Limits for 100-Mbps TransmissionList of Parts and Tools Preparing for InstallationC H A P T E R Software and Hardware Requirements Safety Warnings Safety GuidelinesElectrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance VIP2 and the PA-FE Port Adapters Installation OverviewC H A P T E R ENABLED Installation OverviewFigure 3-1 VIP2-15 or VIP2-40 with a PA-FE-TX in Port Adapter Slot LINKFigure 3-2 VIP2-15 or VIP2-40 with a PA-FE-FX in Port Adapter Slot Installation OverviewFigure 3-3 VIP2-50 with an PA-FE-TX in Port Adapter Slot VIP2 and the PA-FE Port AdaptersRemoving a Port Adapter Removing a Port AdapterFigure 3-4 VIP2-50 with an PA-FE-FX in Port Adapter Slot This completes the procedure for removing a port adapter from a VIP2 Installing a Port Adapter Installing a Port AdapterFigure 3-7 Installing a New Port Adapter Step 4 Carefully slide the new port adapter into the port adapter slot until the connector on the port adapter is completely seated in the connector on the motherboard Installing a Port Adapter Installation Overview Cisco 7200 Series and the PA-FE Port AdaptersC H A P T E R Cisco 7200 Series and the PA-FE Port AdaptersRemoving a Port Adapter Figure 4-1 Cisco 7206 with a PA-FE-TX in Slot Removing a Port AdapterFigure 4-2 Cisco 7206 with an PA-FE-FX in Slot PA-FE-TX port adapterH6420 H6596FAST ETHERNET INPUT/OUTPUT CONTROLLER Slot Installing a Port Adapterguide H6597H6747 Installing a Port Adapter Installation Overview Cisco uBR7200 Series and the PA-FE Port AdaptersC H A P T E R Cisco uBR7200 Series and the PA-FE Port AdaptersH11503 Removing a Port AdapterH11504 Figure 5-3 Placing the Port Adapter Retention Clip in the Unlocked Removing a Port AdapterPosition-Cisco uBR7246 H11518Installing a Port Adapter Metal carrier Inside slot guide PC boardH11519 16177 H11517Installation Overview Cisco 7100 Series and the PA-FE-TX and PA-FE-FXC H A P T E R Figure 6-1 Cisco 7120 Series Router-Port Adapter Slot 3 LocationRemoving a Port Adapter Installing a Port Adapter RCVR GuidesXMTR PA-FE Port Adapter RJ-45 and MII Connections Installing PA-FE Port Adapter Interface CablesAttaching PA-FE Port Adapter Interface Cables C H A P T E RAttaching PA-FE Port Adapter Interface Cables This completes the PA-FE port adapter cable installation Attaching PA-FE Port Adapter Interface Cables C H A P T E R Configuring PA-FE Port Adapter InterfacesCisco 7200 Series and Cisco uBR7200 Series Ports Using the EXEC Command InterpreterPA-FE-TX port adapter port number 4/0 Figure 8-1 Cisco 7206 Fast Ethernet Interface Port Number ExampleFigure 8-2 Cisco uBR7200 Series Fast Ethernet Interface Port Number VIP2 PortsExample-Cisco uBR7246 Figure 8-3 Fast Ethernet Interface Port Number Example-Cisco Cisco 7100 Series PortsPerforming a Basic Configuration Performing a Basic ConﬁgurationFigure 8-4 Port Adapter Slot Numbering-Cisco 7120 Series Figure 8-5 Port Adapter Slot Numbering-Cisco 7140 SeriesUse the following sample basic conﬁguration procedure Conﬁguring PA-FE Media Type Conﬁguring PA-FE Transmission ModeChecking the Conﬁguration Using show Commands to Verify the New Interface Statusadapter slot/interface show running-conﬁg command. DisplayChecking the Configuration Router# show diag VIP2 Show Commands Using the ping Command Router# ping Sending 5, 100-byte ICMP Echoes to 10.0.0.0, timeout is 2 secondsType escape sequence to abort