Cisco Systems PA-FE-TX, PA-FE-FX manual VIP2 Show Commands

Checking the Configuration

VIP2 Show Commands

Use the show interfaces type slot/port-adapter/port command, with arguments such as the interface type (fastethernet, and so forth) and the port number (slot/port), to display information about a specific interface only. The following example of the show interfaces fastethernet command shows information specific to the Fast Ethernet interface on the first PA-FE in slot 3:

Router# show interfaces fastethernet 3/0/0

FastEthernet3/0/0 is administratively down, line protocol is down

Hardware is cyBus FastEthernet Interface, address is 0000.0ca5.2380 (bia 0000) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec), hdx, 100BaseTX ARP type: ARPA, ARP Timeout 4:00:00

Last input 3:08:43, output 3:08:42, output hang never Last clearing of “show interface” counters 2:58:36 Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 watchdog, 0 multicast

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets, 0 restarts 0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Use the show version command to display the configuration of the system hardware (the number of each interface processor type installed), the software version, the names and sources of configuration files, and the boot images. Following is an example of the show version command used with a Cisco 7500 series router:

Router# show version

Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-A), Version 11.1(6)CA Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Fri 06-Oct-95 12:22 by mpo

Image text-base: 0x600088A0, data-base: 0x605A4000

ROM: System Bootstrap, Version 5.3(16645) RELEASED SOFTWARE

ROM: GS Bootstrap Software (RSP-BOOT-M), Version 11.1(6)CA, RELEASED SOFTWARE honda uptime is 4 hours, 22 minutes

System restarted by reload

System image file is “slot0:rsp-a111-1”, booted via slot0

cisco RSP2 (R4600) processor with 32768K bytes of memory. R4600 processor, Implementation 32, Revision 2.0

Last reset from power-on G.703/E1 software, Version 1.0. Bridging software.

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface.

1 VIP2 controllers (1 FastEthernet).

1 FastEthernet/IEEE 802.3 interfaces.

125K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K).

No slave installed in slot 6. Configuration register is 0x2

8-12PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration