Cisco Systems SFS 7024 Installation

CHAPTER

2-7

Cisco SFS 7024 Hardware Users Guide

OL-8794-02

Installation

This chapter describes how to install the Cisco SFS 7024™ and its components, and it includes the

following information:

• Planning the Installation, page 2-8

• Installation Tasks, page 2-15

• Hot Swapping Components, page 2-31

Note Before you install, operate, or service the system, read the Regulatory Compliance and Safety

Information for the Cisco SFS 7012 and SFS 7024 for important safety information.

Contents

Main . Cisco SFS 7024 Hardware Installation Guide Page Page Page Page Page Page Page New and Changed Information Page Preface Audience Organization Conventions Related Documentation Obtaining Documentation Cisco.com Ordering Documentation Documentation Feedback Obtaining Technical Assistance Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Product Overview SFS 7024 Feature Set Strategic Benefits Key Design Features SFS 7024 Product Specifications Mechanical/Thermal/Power Specifications Thermal Management Features Power Design Features Switch Characteristics Chassis Viewer Software Chassis Viewer Functionality Subnet Manager Subnet Management Subnet Management Agents InfiniBand General Services Managers and Agents SNMP Support SNMP MIBs Installation Planning the Installation Environmental Requirements Rack Specifications and Recommendations Installing and Routing Cable Power Requirements Power Supply Uninterruptible Power Supply Installation Tasks Checklist Safety Information Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge Electrical Safety Precautions Tools and Equipment Required Check the Installation Site Unpack the Equipment Installation Tasks Mounting Kit Mounting Hardware Kit Contents: Mark the Rack Install the Rails in the Rack Rack-Mount the Switch Installing the Switch Face Plate Installing the Spine and Leaf Modules Page Removing a Module or Blank 2-19 Connect Equipment to the Ports and Power On the System Figure 2-6 SFS 7024 Chassis Front View Page Connecting Power Bringing Up the System For the First Time Start-up Procedures Changing the SFS 7024 IP Address and Default Gateway via the CLI Updating Management Spine IP Addresses in a Redundant Management Configuration Page 2-25 Verifying Start-up SFS 7024 Component LEDs Chassis Status LED Subnet Manager Agent (SMA) LED RJ45 LEDs Fan LEDs Power Supply LEDs SFS 7024 Leaf and Spine Module LEDs Leaf Module IB Port LEDs Spine and Leaf Module Status LED Spine and Leaf Module Attention LED Spine Module Management LEDs Accessing On-line Help Shutdown Procedures Rebooting Components from Chassis Viewer Rebooting Multiple Managed Spines Hot Swapping Components Hot Swapping Spine and Leaf Modules Hot Swapping the Fan Unit Hot Swapping Power Supplies Operations and Administration Chassis Viewer The Chassis Viewer Manages Home Page ? (Help) Button Support Button Displaying the Leaf and Spine Module Views Leaf Module View Spine Module View Leaf and Spine Module Component Details Area Leaf and Spine Details Header Leaf and Spine Information Area Displaying the Chassis View Chassis View Component Details Area Chassis Details Header Rebooting Components from Chassis Viewer Rebooting Multiple Managed Spines Chassis View Component Information Area Chassis View Component Information Area Tabs LEDs and Sensors Tab System Tab Chassis FRU Tab Power Tab Fan Tab Backplane Tab Modifying Switch Component Information Configuration and Monitoring Features Set Level Page Preset Tab Syslog Tab Configure Syslog on a Linux Server Reset Log Levels Firmware Update SNMP Target Configuration Target Configuration Window Field Descriptions Page Filter Status Setting Community Strings Chassis Traps Page Page SFS 7024 Port Statistics Understanding Port Naming Conventions Port Statistics Field Descriptions InfiniBand Statistics: Page Leaf and Spine Module IB Port Statistics Leaf Modules Spine Modules Set Field Thresholds Page Time Service Page Page Configuring the Switch OOB IP Address Configuring the Switch Default Gateway IP Address Page Spine View Menu Logging Viewing the Log Purging the Log Select Boot Image License Keys; Key Administration Adding a New License Key Deleting a License Key Page A Technical Specifications Page B Command Line Interface Overview Commands and Functional Groups Online Help Keyboard Shortcuts Accessing the CLI B-80 Type the appropriate username and press Enter. Step 3 The system prompts for a password. The CLI has the following default passwords: Groups and Commands General Firmware B-81 IbSwitchInfo Chassis B-82 Log Note When configuring log devices (option 1), do not change settings for the following devices: KeyManagement TimeManagement SNMP Capture Deprecated Page C Troubleshooting Power Supply Hardware Checks Switch Fan OOB Ethernet RJ45 Port SFS 7024 Leaf Module IB Ports Troubleshooting Scenarios InfiniBand Invalid IP Address entered for SWC via Console Port Bad IB Cable Improperly Seated IB Cable