Citizen Systems Model CMP-10 manual

BYTE 4

BIT7

BIT6

BIT5

BIT4

BIT3

BIT2

BIT1

BIT0

Not in use (0)

Not in use (0)

Not in use (0)

Not in use (0)

Not in use (1)

Not in use (0)

Not in use (0)

Not in use (0)

[Caution]	¥	If any status item is enabled, the status is sent to the host when this command is
		executed. After that time on, the status is sent each time an enabled status item
		changes. Because each status item represents the current condition, status items
		disabled for ASB may also have changed.
	¥	The ASB function is disabled if all status items are disabled.
	¥	The printer sends 4 bytes of status shown in the tables below, without checking
		whether the host is ready to receive or busy. The 4 bytes of status is a continuous
		string except for XOFF code.
	¥	Because this command is executed when data is mapped in the receive buffer,
		there may be a delay between command receiving and status sending depending
		on the condition of the receive buffer.
	¥	Even if the printer is excluded from the selection of peripheral equipment (ESC =),
		the 4 bytes of status is sent to the host whenever status changes.

Ñ 53 Ñ

Image 55

Citizen Systems Model CMP-10 manual Disabled for ASB may also have changed

Contents

Command Reference Revision Code Command Function CMP-10 Command SET GS L GS HGS W Xxxx ALL Command Details BEL Print Results Sample Program 0AH ESC RS ESC SP n Default Sample Program ESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize command ESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = n 21 Ñ Hex Track ESC ? n ESC @ See Also Sample Program Print Results ESC D n k NUL ESC E n ESC G n ESC R n ESC J nHex Character Set Model CMP-10 Ver ESC S nESC T Hex Speed bps Hex Condition ESC V n ESC Y n Byte ESC Z Update via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a n ESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFF See Also Sample Program GS * n1 n2 d n1 n2 D1 ...... Dn Hex Name Dot Density Vertical Direction Horizontal Direction GS / m 1DH3AH Hex Printing Position GS H n GS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex Mode Bit Status Item Addressed by ABS GS a n Not in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n 1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C Hex CODE93 CODE128 Type Print Sample Outline of Symbol Max. ColumnDescriptionof Bar Codes JAN-8 GS w nL nH AT*PAIRINFO=0 AT command Function Factory defaultAT*PAIRINFO=1 Example Bluetooth Init Commands ESC l n Black Mark Function Distance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lost Memory switch 8 = Memory switches OFF0 ON1 Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable 14, 15 pin Communicate mode setting Explanation of Input/Output Signals RS-232C Circuit Electrical Characteristics IrComm 3 Wire raw IrLPT Infrared Communication Specifications Mcbf Mechanical Specification Battery Power Related Specifications EMI Standard AC AdaptorUL, C-UL, PSE 10AD-JU