IrComm 3 Wire raw IrLPT | Citizen Systems Model CMP-10 specification

7.INFRARED COMMUNICATION SPECIFICATIONS

7.1Basic Specification

(1)	Interface:	Infrared transceiver mode
(2)	Data transfer system	Half duplex
		Asynchronous
(3)	Baud rate:	9600, 19200, 38400, 57600, 115200 bps
		(Max baud rate can be set at 57600 bps by command.)
(4)	Data configuration	Data length	8 bit
		Stop bit	1 bit
		Parity	None
(5)	Logic level	Low Level = 0
		High Level = 1
(6)	Transport wave:	Wave length 850 - 900 nm
(8)	Distance	Less than 80 cm
(9)	Receiving angle	Left 15¼	Right 15¼
		Top 15¼	Bottom 15¼

7.2 Supported Protocol

(1)	IrDA version	1.0
(2)	Flow control	IrDA standard
(3)	Supported Protocol	IrComm 3 wire raw
		IrLPT
		IrLMP
		IrLAP

(4)Protocol Layer

IrComm 3 Wire raw

IrLPT

	Ir Link Management - MUX - IrLMP
	Ir Link Access Protocol - IrLAP
		Async Serial-IR
		9600-115.2 kb/s
(5) Applicable protocol	Class:	IrDA:IrCOMM or IrDA:IrLPT
	Attribute:	IrDA:IrLMP:LsapSel
		via IrLMP

Ñ 75 Ñ

Image 77

Citizen Systems Model CMP-10 manual Infrared Communication Specifications, IrComm 3 Wire raw IrLPT

Contents

Command Reference Revision Code Command Function CMP-10 Command SET GS W GS HGS L Xxxx ALL Command Details BEL Print Results Sample Program 0AH ESC RS ESC SP n Default Sample Program Bit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize command Max. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = n 21 Ñ Hex Track ESC ? n ESC @ See Also Sample Program Print Results ESC D n k NUL ESC E n ESC G n Hex Character Set ESC J nESC R n ESC T ESC S nHex Speed bps Model CMP-10 Ver Hex Condition ESC V n ESC Y n Byte ESC Z Update via firmware interface Not in use Reserved, always 33 Ñ ESC \ n1 n2 ESC ` Hex Position ESC a n ESC c5 n ESC d n ESC ESC x n B B B GS n m Memory Switch OFF See Also Sample Program GS * n1 n2 d n1 n2 D1 ...... Dn Hex Name Dot Density Vertical Direction Horizontal Direction GS / m 1DH3AH Hex Printing Position GS H n GS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex Mode Bit Status Item Addressed by ABS GS a n Not in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n 1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C Hex Descriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnJAN-8 CODE93 CODE128 GS w nL nH AT*PAIRINFO=1 AT command Function Factory defaultAT*PAIRINFO=0 Example Bluetooth Init Commands ESC l n Black Mark Function Distance from PE sensor and print head is approx .5 mm Character Codes Table Setup menu function After Ver2.20 Change IrDA MAX Speed ? If YES is not chosen, the changed setting will not be lost Memory switch 8 = Memory switches OFF0 ON1 Change Print Density ? Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable 14, 15 pin Communicate mode setting Explanation of Input/Output Signals RS-232C Circuit Electrical Characteristics IrComm 3 Wire raw IrLPT Infrared Communication Specifications Mcbf Mechanical Specification Battery Power Related Specifications UL, C-UL, PSE 10AD-JU AC AdaptorEMI Standard