Clarion DRX9675z owner manual Basic Operations

7. OPERATIONS

Basic Operations

Basic Operations	Note: Be sure to read this chapter referring to the front diagrams of
	chapter “3. CONTROLS” on page 5 (unfold).

∗ Once selected, the preferred display becomes

the display default. When a function adjustment

such as volume is made, the screen will

Adjusting the balance

1. Press MODE button & three times and select

“BAL DETAIL”.

4

CAUTION

Be sure to lower the volume before switch- ing off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and dam-

2. Each time you press FUNCTION button 7,

the mode of operation changes in the following

order:

Radio (TUNER) mode ➜ CD mode ➜ CD

changer mode ➜ MD changer mode ➜ TV

mode ➜ Radio (TUNER) mode...

∗ External equipment not connected with CeNET

is not selected.

momentarily switch to that function’s display,

then revert back to the preferred display sev-

eral seconds after the adjustment.

∗ If a title has been input, it is displayed in the main

display. If no title has been input, “------------”

appears in the display. To input a title, refer to

the subsection in “Entering titles” in “Other

Handy Functions” section.

2.	Press the right side of SEARCH button to
	select “0”.
3.	Pressing VOLUME button 2 up (w) empha-
	sizes the sound from the right speaker;
	pressing it down (z) emphasizes the sound
	from the left speaker.
	∗ The factory default setting is “0”. (Adjustment
	range: LEFT13 to RIGHT13)

age the unit.

Changing the angle of the SLOPING

4. When the adjustment is complete, press

The clock is displayed when the ignition key is turned to the ACC (accessory) or IGN (igni- tion-on) position even when the unit power is off. In some cars, the clock may momen- tarily disappear when the ignition key is turned to the START position. The clock will reappear after the engine has started and the ignition key is released to the IGN (ignition- on) position.

Turning on/off the power

Note:

•Be careful about using this unit for a long time with- out running the engine. If you drain the car’s bat- tery too far, you may not be able to start the en- gine and this can reduce the service life of the battery.

1.Press POWER button 7.

2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.

3.Press and hold POWER button 7 for 1 sec- ond or longer to turn off the power for the unit or press POWER OFF button 9.

Note:

•About the system check

The confirmation of connected equipments must be performed for this unit only when the wiring connection is complete and power is turned on to the unit first. When the power is supplied,

“SYSTEM CHECK” appears in the display. Press POWER button 7. The system check starts inside

the unit. The equipments connected to this unit appears in the display. Press POWER button 7 again.

Adjusting the volume

Pressing VOLUME button 2 up (w) increases the volume; pressing it down (z) decreases the volume.

∗The volume level is from 0 (minimum) to 33 (maxi- mum).

Switching the display

Press DISP button 3 to select the desired display. Each time you press DISP button 3, the display switches in the following order:

Main display

MANU

F M 1 B B C

FM1 80. 0

1 2 3 4 5 6 P.ch

Clock display

MANU

F M 1 B B C

FM1 PM 7 : 50

1 2 3 4 5 6 P.ch

Spectrum analyzer display

Screen saver display

CONSOLE

If the installation position or display angle makes the display hard to see, change the angle of the

SLOPING CONSOLE.

1.Press and hold OPEN (ANGLE) button 6 for 2 seconds or longer.

2.Each time this button is pressed, the SLOPING CONSOLE switches to the tilted or closed state.

CAUTION

When not using this unit for a long time and when turning OFF the ignition key for the car, close the SLOPING CONSOLE for safety’s sake.

Switching the screen saver

You can switch between 3 screen savers.

1.Press DISP button 3 and select the screen saver display.

2.Each time you press and hold DISP button 3 for 1 second or longer, the screen saver changes between 3 screen savers.

Adjusting the EXTRA output volume

You can adjust the volume output from the unit’s non-fader output terminal.

1.	Press MODE button & three times and select
	“EXTRA VOL” while in Audio Mode.
2.	Press the right side of SEARCH button 4 to
	select “0”.
3.	Pressing VOLUME button 2 up (w) increases
	the output volume; pressing it down (z)
	decreases the output volume.
	∗

MODE button & several times or press and

hold ENT button $ for 1 second or longer until

the function mode is reached.

Adjusting the fader

1.Press MODE button & three times and select “FAD DETAIL”.

2.Press the right side of SEARCH button 4 to select “0”

3.Pressing VOLUME button 2 up (w) empha- sizes the sound from the front speakers; pressing it down (z) emphasizes the sound from the rear speakers.

∗The factory default setting is “0”. (Adjustment range: FRONT12 to REAR12)

4.When the adjustment is complete, press MODE button & several times or press and hold ENT button $ for 1 second or longer until the function mode is reached.

Selecting a mode
1. Press FUNCTION button 7 to change the
mode of operation.	Main display...

The factory default setting is “0”. (Setting range:

–5 to +5)

4. When the adjustment is complete, press MODE

button & several times or press and hold ENT

button $ for 1 second or longer until the function

mode is reached.

10 DRX9675z DRX9675z 11