Manuals / Compatible Systems / Computer Equipment / Server

Compatible Systems A00-1869 manual IntraPort Enterprise-8 Switch Settings

Models: Enterprise-8 A00-1869

1 44

Download 44 pages 1.69 Kb

Page 37

Image 37

Chapter 8 - LED Patterns and Test Switch Settings

IntraPort Enterprise-8 Switch Settings

The switch for Ethernet 0:0 controls the entire device. For example, if you set the switch for Ethernet 0:0 to “3” and download new software to the device, the other interfaces will auto- matically receive the software update from Ethernet 0:0 via the backplane. In general, the only time you should use an individual RIOP card’s switch is when the card is unable to communi- cate with the backplane for some reason.

0Normal Operation

1Unused*

2Unused*

3Run Boot ROM Downloader

4Unused*

5Erase Flash ROM (OS and Configuration)

6Erase Flash ROM (Configuration Only)

7Unused*

8Unused*

9Allow letmein password for 5 minutes after powerup

ΜCaution: Settings marked with an asterisk may erase your Flash ROM. Please do not use these settings without first contacting Compatible Systems’ Technical Support.

Page 37

Image 37

Compatible Systems A00-1869 manual IntraPort Enterprise-8 Switch Settings

Contents

Compatible Systems Corporation 4730 Walnut Street Suite IntraPort Enterprise-8 VPN Access Server Installation GuideBoulder, Colorado Copyright 1999, Compatible Systems Corporation IntraPort Enterprise-8 VPN Access Server Installation Guide, VersionPart number A00-1869 Chapter 4 - CompatiView Software Installation Chapter 3 - Network InstallationChapter 5 - Command Line Management Introduction to the IntraPort Enterprise-8Chapter 7 - Shipping Defaults Chapter 6 - Basic Configuration GuideChapter 8 - LED Patterns and Test Switch Settings Appendix A - Connector and Cable Pin OutsAppendix D - Adding or Replacing RIOP Cards Appendix E - When the “Over Temp” Light Comes OnAppendix F - Terms and Conditions Table of ContentsFigure 1. Location of Voltage Switch on the Power Supply Introduction to the IntraPort Enterprise-8 IntraPort Enterprise-8 Installation OverviewA Note About Remote Client Connections Chapter 3 - Network Installation IntraPort Enterprise-8 Manual OverviewChapter 4 - CompatiView Software Installation Chapter 5 - Command Line PreparationA Few Notes Chapter 1 - Getting StartedWarranty and Service Please Read the ManualsAdditional Items Needed for Installation What You Will Need to Get StartedSupplied with the IntraPort Enterprise-8 Safety Guidelines Placement ConsiderationsChapter 2 - Mounting Instructions Parts and Tools Changing the Power Supply Voltage SettingsFigure 1. Location of Voltage Switch on the Power Supply Figure 2.1. Installing Mounting Ears for a Telco Rack Installing Mounting Ears and HandlesFigure 3. Rack-Mount Brackets Rack-Mount BracketsFigure 4. Fastening the Right Bracket to the Rack Right Bracket InstallationFigure 5. Fastening the Left Bracket to the Rack Left Bracket InstallationFigure 6. Lowering the Shelf Securing the ShelfFigure 6.1. Securing the Shelf Figure 7. Moving the Unit into a Standard Equipment Rack Moving the Unit into the RackFigure 7.1. Moving the Unit into a Telco Rack Figure 8. Placing the Unit in a Standard Equipment Rack Placing the Unit in an Equipment RackFigure 8.1. Placing the Unit in a Telco Rack Figure 9. Securing the Unit to the Rack Securing the Unit to the RackPhysical Connection Requirements Chapter 3 - Network InstallationFigure 11. Detail of RIOP Cards Connecting the Server to the EthernetPowering Up the Server Connecting a Management ConsolePower Alarm Information Installation and Operation Chapter 4 - CompatiView Software InstallationCompatiView for Windows System RequirementsTransport Protocols and CompatiView Out-of-Band Command Line Management Chapter 5 - Command Line ManagementTemporarily Reconfiguring a Host for Command Line Management Setting Up Telnet Operation Ethernet Interface Configuration Chapter 6 - Basic Configuration GuideIP Protocol IP Settings for Setups in Parallel with a FirewallIP Ethernet 60 section IP Settings for Setups Behind a FirewallIPX Protocol Configuring the Server for LAN-to-LAN TunnelsAppleTalk Protocol Required for LAN-to-LAN Tunnel ConfigurationsRequired for Client Tunnel Configurations Configuring the Server for IP and IPX Client TunnelsSuggested for Client Tunnel Configurations VPN User DatabaseSetting the IntraPort Enterprise-8 for a RADIUS Server Setting up RADIUS AuthenticationRADIUS Server User Authentication Settings Setting the IntraPort Enterprise-8 for an ACE/Server Setting up SecurID AuthenticationACE/Server Settings TB Use the save command Saving a Configuration File to Flash ROMCV Use the Save to/Device option from the File menu Default Password Chapter 7 - Shipping DefaultsIP Defaults IPX DefaultsGeneral Indicators Chapter 8 - LED Patterns and Test Switch SettingsEthernet Traffic Indicators Load % IndicatorsIntraPort Enterprise-8 Switch Settings Pin Outs for DB-25 Male to DB-25 Female Console Cable Appendix A - Connector and Cable Pin OutsAppendix B - Downloading Software From Compatible Systems Appendix B - Downloading Software From Compatible SystemsAppendix C - Security Dynamics ACE/Server Information Appendix C - Security Dynamics ACE/Server InformationAppendix D - Adding or Replacing RIOP Cards Appendix D - Adding or Replacing RIOP CardsAppendix E - When the “Over Temp” Light Comes On Replacing or Cleaning the Intraport Enterprise-8 Air FilterAppendix E - When the “Over Temp” Light Comes On Appendix F - Terms and Conditions Appendix F - Terms and Conditions3. Payment Terms. Payment shall be made prior to shipment or upon delivery, unless otherwise agreed to in writing. Payment shall not constitute acceptance of the goods