DBC Network Bridge

4Operation

4.2Back Panel Controls and Connectors

J. IEC AC Power Inlet

Accepts an IEC AC power cord. The DBC Network Bridge has a universal power supply, and may be operated on AC line voltages from 100 VAC to 240 VAC at 50 Hz or 60 Hz.

K. Multifunction Control Port

One DB37M for analog inputs, digital inputs, +5VDC, +10VDC and ground. 8 input-switch closures, 8 analog 0-10VDC inputs, 16 output contact closures, +10VDC power source (1A), GND (1A+).

L. Primary Network Connector

RJ45 connector for primary CobraNet network connections (100Mbit CAT 5). Supports TCP/IQ communications with CobraNet digital audio channels.

On the connector are two LEDs (see detail drawing below). The left LED lights yellow when the port is in use and will blink if the device is also the conductor (the CobraNet timing master device). The right LED lights green when link is established and blinks when network activity is detected. Both LEDs flash yel- low in unison to report a fatal error.

M. Secondary Network Connector

RJ45 connector for secondary (redundant or backup) CobraNet network con- nections (100Mbit CAT 5). Supports TCP/IQ communications with CobraNet digital audio channels.The SECONDARY connection is similar to the Primary, but is active only in case of a fault in the CobraNet network attached to the PRIMARY. The secondary LEDs work in the same way as the primary ones.

N. AES/EBU Digital Audio Input

DB25 female connector accepts eight AES3 digital audio signals. Pinout matches Dolby #778 AES input/output card for CP-650.

O. Analog Audio Input

DB25 female connector accepts eight balanced analog line-level analog inputs. Pinout matches Dolby CP-650 analog output.

P. Aux Input Level Controls

Screwdriver-set, calibrated gain potentiometer (one per channel) for adjusting the input gain to the input signal level. These can be used to compensate for different microphone sensitivities. Control range is from –12 dB to +20 dB.

Figure 4.2 Back Panel Controls and Connectors

Q. Aux Inputs

2 female XLR balanced inputs for speech reinforcement or announcements. Switchable between mic, line, and mic with phantom power.

R. Monitor Out Connector

3-pin Phoenix-type connector supplies a balanced analog line-level output signal which can feed a powered monitor loudspeaker. This output can be switched to monitor:

Cinema processor output signals (+20 dBu maximum output level)

Pre-amp input signals

Post-amp output signals

S. Aux Input Mic/Line/Phantom Switch

Each input has a three-position “M L P” selector switch for mic level, line level, or mic level with phantom power.

Select the M position for microphone signal levels up to +7dBu (0 dbu = 0.775 volt).

Select the L position for line level signals up to +32 dBu

Select the P position for mic inputs that require +24 VDC phantom power.

Operation Manual

page 21

Page 21
Image 21
Crown 137769-3 Back Panel Controls and Connectors IEC AC Power Inlet, Multifunction Control Port, Analog Audio Input

137769-3 specifications

Crown 137769-3 is a state-of-the-art electric forklift designed to meet the demands of modern material handling and warehouse operations. Known for its robust performance and advanced technology, this model is favored by businesses seeking efficiency and reliability.

One of the standout features of the Crown 137769-3 is its exceptional lifting capacity. With the ability to lift heavy loads with ease, it is perfect for high-capacity warehouses and industrial environments. The forklift also boasts an impressive lifting height, allowing for the stacking of goods in high racks, maximizing vertical space and optimizing storage solutions.

The ergonomics of the Crown 137769-3 are meticulously designed to enhance operator comfort and productivity. The spacious operator compartment offers ample legroom and an adjustable seat, reducing fatigue during long shifts. Additionally, the intuitive controls and clear visibility contribute to a safer and more efficient working environment, minimizing the risk of accidents.

Crown’s innovative technologies are at the forefront of the 137769-3's appeal. It features the Crown Engineered Reliability (Crown ER) system, which ensures that critical components are built to last, significantly reducing maintenance needs and downtime. The integrated monitoring system provides real-time data on performance, vehicle status, and battery life, enabling managers to optimize operations effectively.

Another key technology featured in this model is the smart traction control system, designed to provide enhanced stability and control, particularly in uneven terrains. This feature is essential for preventing tip-overs and ensuring the safety of both the operator and the loads being transported.

The Crown 137769-3 is powered by long-lasting batteries that offer impressive run times, allowing for extended usage without frequent recharging. This efficiency helps businesses maximize productivity while minimizing energy costs.

In summary, the Crown 137769-3 combines impressive lifting capabilities, advanced ergonomics, robust technology, and energy efficiency, making it an ideal choice for any warehouse operation. Its reliability, safety features, and user-friendly design contribute to a seamless operational experience, ensuring that businesses can keep pace with the demands of modern logistics and distribution. This model stands out as an excellent investment for companies striving for excellence in material handling.