Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

c.When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

d.Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

e.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

f.Never fuel machine indoors.

g.Never remove gas cap or add fuel while the engine is hot or running. Allow engine to cool at least two minutes before refueling.

h.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to allow space for fuel expansion.

i.Replace gasoline cap and tighten securely.

j.If gasoline is spilled, wipe it off the engine and equipment. Move unit to another area. Wait 5 minutes before starting the engine.

k.To reduce fire hazards, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.

l.Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

Operation

1.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2.Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3.Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4.If it becomes necessary to push material through the shredder hopper, use a small diameter stick. Do not use your hands or feet.

5.If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

a.Inspect for damage.

b.Repair or replace any damaged parts.

c.Check for any loose parts and tighten to assure continued safe operation.

6.Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

7.Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

8.Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

9.Never operate without the shredder hopper, chipper chute, or chute deflector properly attached to the machine. Never empty or change discharge bag while the engine is running.

10.Keep all guards, deflectors and safety devices in place and operating properly.

11.Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12.Never operate this machine without good visibility or light.

13.Do not operate this machine on a paved, gravel or non- level surface.

14.Do not operate this machine while under the influence of alcohol or drugs.

15.Muffler and engine become hot and can cause a burn. Do not touch.

16.Never pick up or carry machine while the engine is running.

17.If situations occur which are not covered in this manual, use care and good judgement. Contact Customer Support for assistance and the name of the nearest service dealer.

Maintenance & Storage

1.Never tamper with safety devices. Check their proper operation regularly.

2.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.

4

Section 2 — Important Safe Operation Practices

Page 3 Page 5
Page 4
Image 4
Cub Cadet CS3210, CS 2210 warranty Operation, Maintenance & Storage, Safe Handling of Gasoline
Page 3 Page 5

CS 2210, CS3210 specifications

Cub Cadet has earned a reputation in the lawn care and outdoor power equipment market for producing reliable and high-performance machinery. The Cub Cadet CS3210 and CS2210 models are no exception, standing out as premier options for both residential and commercial users seeking versatility and efficiency in their operations.

The CS3210 is equipped with a powerful 31-horsepower Kohler engine, delivering exceptional performance and reliability. This engine is designed to handle various mowing conditions, making it suitable for handling both thick grass and uneven terrain. The CS2210, while slightly smaller, boasts a strong 22-horsepower engine that efficiently manages medium-sized yards without compromising performance.

A standout feature of both models is their advanced hydrostatic transmission, which allows for smooth, effortless driving. This system enhances user comfort, especially during extended mowing sessions, by providing seamless shifting and superior maneuverability. Users will appreciate the easy-to-use foot-operated controls that allow for precise speed adjustments.

Both the CS3210 and CS2210 come with a durable, reinforced cutting deck, which ensures a clean cut and improved grass mulching. The cutting deck features a stamped design that enhances airflow, promoting better clippings distribution. With adjustable cutting heights, users can customize their mowing experience to achieve a tailored finish that suits their lawn preferences.

In addition to mowing, these models offer flexibility for various lawn care tasks. They can be equipped with a variety of attachments, including baggers, snow throwers, and tillers, transforming them into multi-functional machines capable of handling seasonal chores and yard work.

Safety is a top priority with both the CS3210 and CS2210. Each model is designed with user-friendly controls and features such as a safety switch that prevents accidental starts, enhancing the overall user experience while ensuring peace of mind.

Overall, the Cub Cadet CS3210 and CS2210 are robust, reliable, and versatile lawn tractors designed to tackle a range of outdoor tasks. With their powerful engines, advanced transmissions, and durable construction, they represent a solid investment for anyone looking to maintain their lawn efficiently. Whether you're a homeowner or a professional landscaper, these models provide the features and technology necessary to achieve top-notch results.
Top Page Image Contents