Cypress manual CY7C1316JV18, CY7C1916JV18, CY7C1318JV18, CY7C1320JV18, Pin Definitions

CY7C1316JV18, CY7C1916JV18

CY7C1318JV18, CY7C1320JV18

Pin Definitions

Pin Name

IO

Pin Description

DQ[x:0]

Input Output-

Data Input Output Signals. Sampled on the rising edge of K and

clocks during valid write operations.

K

Synchronous

These pins drive out the requested data during a read operation. Valid data is driven out on the rising

edge of both the C and C clocks during read operations or K and K when in single clock mode. When

read access is deselected, Q[x:0] are automatically tri-stated.

CY7C1316JV18 − DQ[7:0]

CY7C1916JV18 − DQ[8:0]

CY7C1318JV18 − DQ[17:0]

CY7C1320JV18 − DQ[35:0]

Input-

Synchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition

LD

Synchronous

includes address and read/write direction. All transactions operate on a burst of 2 data.

0,

Input-

Nibble Write Select 0, 1 − Active LOW (CY7C1316JV18 only). Sampled on the rising edge of the K and

NWS

NWS1

Synchronous

K clocks during write operations. Used to select which nibble is written into the device during the current

portion of the write operations. Nibbles not written remain unaltered.

NWS0 controls D[3:0] and NWS1 controls D[7:4].

All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select

ignores the corresponding nibble of data and it is not written into the device.

0,

Input-

Byte Write Select 0, 1, 2, and 3 − Active LOW. Sampled on the rising edge of the K and

clocks during

BWS

K

BWS1,

Synchronous

write operations. Used to select which byte is written into the device during the current portion of the Write

BWS2,

operations. Bytes not written remain unaltered.

BWS3

CY7C1916JV18 − BWS0

controls D[8:0]

CY7C1318JV18 − BWS0

controls D[8:0] and

BWS

1 controls D

[17:9].

CY7C1320JV18 − BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18] and BWS3 controls

D[35:27].

All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select

ignores the corresponding byte of data and it is not written into the device.

A, A0

Input-

Address Inputs. These address inputs are multiplexed for both read and write operations. Internally, the

Synchronous

device is organized as 2M x 8 (2 arrays each of 1M x 8) for CY7C1316JV18 and 2M x 9 (2 arrays each

of 1M x 9) for CY7C1916JV18, 1M x 18 (2 arrays each of 512K x 18) for CY7C1318JV18, and 512K x 36

(2 arrays each of 256K x 36) for CY7C1320JV18.

CY7C1316JV18 – Because the least significant bit of the address internally is a ‘0’, only 20 external

address inputs are needed to access the entire memory array.

CY7C1916JV18 – Because the least significant bit of the address internally is a ‘0’, only 20 external

address inputs are needed to access the entire memory array.

CY7C1318JV18 – A0 is the input to the burst counter. These are incremented internally in a linear fashion.

20 address inputs are needed to access the entire memory array.

CY7C1320JV18 – A0 is the input to the burst counter. These are incremented internally in a linear fashion.

19 address inputs are needed to access the entire memory array. All the address inputs are ignored when

the appropriate port is deselected.

Input-

Synchronous Read/Write Input. When

is LOW, this input designates the access type (read when

R/W

LD

Synchronous

R/W is HIGH, write when R/W is LOW) for the loaded address. R/W must meet the setup and hold times

around the edge of K.

CInput Clock Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from the device. C and C can be used together to deskew the flight times of various devices on the board back to the controller. See Application Example on page 9 for more information.

CInput Clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from the device. C and C can be used together to deskew the flight times of various devices on the board back to the controller. See Application Example on page 9 for more information.

K	Input Clock Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
	and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising
	edge of K.

KInput Clock Negative Input Clock Input. K is used to capture synchronous data being presented to the device and to drive out data through Q[x:0] when in single clock mode.

Document Number: 001-15271 Rev. *B Page 6 of 26

[+] Feedback