D-Link DWS-3000 manual Unified Switch Installation, Quick Starting the Networking Device

Models: DWS-3000

1 174
Download 174 pages 3.77 Kb
Page 21
Image 21

1 Getting Started

Unified Switch Installation

This section contains procedures to help you become acquainted quickly with the switch software.

Before installing the Unified Switch, you should verify that the switch operates with the most recent firmware.

Quick Starting the Networking Device

1.Configure the switch for In-band or Out-of-Band connectivity. In-band connectivity allows access to the Unified Switch locally or from a remote workstation. You must con- figure the device with IP information (IP address, subnet mask, and default gateway).

2.Turn the Power ON.

3.Allow the device to load the software until the login prompt appears. The device initial state is called the default mode.

4.When the prompt asks for operator login, do the following steps:

-Type admin at the login prompt. Since a number of the Quick Setup commands require administrator account rights, D-Link suggests logging into an administrator account.

Do not enter a password because the default mode does not use a password - after typ- ing admin, press Enter two times.

-The CLI User EXEC prompt is displayed.

-Type enable to switch to the Privileged EXEC mode from User EXEC.

-Type configure to switch to the Global Config mode from Privileged EXEC.

-Type exit to return to the previous mode.

-Enter ? to show a list of commands that are available in the current mode.

NOTE: For more information about the configuration modes, see the CLI Command Reference.

System Information and System Setup

This section describes the commands you use to view system information and to setup the network device. The tables below contain the Quick Start commands that allow you to view or configure the following information:

Software versions Physical port data

User account management IP address configuration

Uploading from Networking Device to Out-of-Band PC (Only XMODEM) Downloading from Out-of-Band PC to Networking Device (Only XMODEM) Downloading from TFTP Server

Restoring factory defaults

For each of these tasks, a table shows the command syntax, the mode you must be in to execute the command, and the purpose and output of the command. If you configure any network parameters, you should execute the write command.

Unified Switch Installation

21

Page 21
Image 21
D-Link DWS-3000 Unified Switch Installation, Quick Starting the Networking Device, System Information and System Setup

DWS-3000 specifications

The D-Link DWS-3000 is an advanced cloud-ready wireless switch designed to meet the increasing demands of modern networks. As organizations transition to more mobile and connected environments, the need for robust and scalable networking solutions becomes paramount. The DWS-3000 addresses this need with its range of features, technologies, and specifications tailored for seamless network management.

One of the standout features of the DWS-3000 is its support for centralized management, allowing IT administrators to oversee multiple access points from a single interface. This simplifies the process of provisioning, monitoring, and troubleshooting network devices, ensuring optimal performance and minimizing downtime. The switch's intuitive web interface and support for D-View, D-Link's network management software, enable effective control over network operations.

The DWS-3000 is equipped with advanced security protocols to safeguard sensitive data within the network. It supports WPA3 encryption, which enhances security compared to its predecessor, WPA2. Additionally, features like MAC address filtering, 802.1X authentication, and rogue AP detection provide comprehensive protection against unauthorized access.

In terms of performance, the DWS-3000 leverages high-capacity hardware to support PoE (Power over Ethernet) technology, enabling power delivery to compatible devices without the need for additional cabling. This feature is particularly beneficial for deployment scenarios where cabling infrastructure is limited.

Moreover, the DWS-3000 is built with scalability in mind. It can support a vast number of access points, making it suitable for deployments ranging from small businesses to large enterprises. This scalability, combined with features like load balancing and Band Steering, ensures efficient use of available bandwidth, enhancing user experience.

The switch also offers seamless integration with D-Link’s suite of access points, allowing for simplified deployments in various environments, whether indoor or outdoor. The capabilities of the DWS-3000 extend into a comprehensive analytics engine, which provides insights into network performance and user behavior, aiding in informed decision-making.

With its blend of advanced features, robust security measures, and scalability, the D-Link DWS-3000 is positioned as a powerful solution for organizations looking to elevate their network infrastructure. It empowers businesses to provide reliable, high-performance wireless connectivity while maintaining security and ease of management in today’s dynamic environment.