Dell WorkStation 410 manual Ulyh$Gguhvvlqj, Qvwdoolqjdq,+Duglvnulyhlqwkh+Duglvn Ulyh%Udfnhw

Up to two 1.6-inch EIDE drives can be installed in the internal hard-disk drive cage that is next to the externally accessible 5.25-inch drive bays.

(,'(￿'ULYH￿$GGUHVVLQJ

All EIDE devices should be configured for the cable select jumper position, which assigns master and slave status to devices by their position on the EIDE cable. When two EIDE devices are connected to a single EIDE cable and are configured for the cable select jumper position, the device attached to the last connector on the inter- face cable is the master or boot device (drive 0) and the device attached to the middle connector on the interface cable is the slave device (drive 1). Refer to the drive docu- mentation in your upgrade kit for information on setting devices to the cable select jumper position.

With the two EIDE interface connectors on the system board, your system can sup- port up to four EIDE devices. EIDE hard-disk drives should be connected to the EIDE interface connector labeled “IDE1.” (EIDE tape drives and CD-ROM drives should be connected to the EIDE interface connector labeled “IDE2.”)

,QVWDOOLQJ￿DQ￿(,'(￿+DUG￿'LVN￿'ULYH￿LQ￿WKH￿+DUG￿'LVN￿ 'ULYH￿%UDFNHW

Install an EIDE hard-disk drive in the hard-disk drive bracket as follows:

￿￿,I￿\RX￿DUH￿UHSODFLQJ￿D￿KDUG￿GLVN￿GULYH￿WKDW￿FRQWDLQV￿GDWD￿\RX￿ZDQW￿WR￿ NHHS￿￿EH￿VXUH￿WR￿PDNH￿D￿EDFNXS￿RI￿\RXU￿ILOHV￿EHIRUH￿\RX￿FRQWLQXH￿ZLWK￿

WKLV￿SURFHGXUH￿

￿￿3UHSDUH￿WKH￿GULYH￿IRU￿LQVWDOODWLRQ￿

&$87,216￿￿*URXQG￿\RXUVHOI￿E\￿WRXFKLQJ￿DQ￿XQSDLQWHG￿PHWDO￿VXUIDFH￿ RQ￿WKH￿EDFN￿RI￿WKH￿FRPSXWHU￿￿

:KHQ￿\RX￿XQSDFN￿WKH￿GULYH￿￿GR￿QRW￿VHW￿LW￿RQ￿D￿KDUG￿VXUIDFH￿￿ZKLFK￿PD\￿ GDPDJH￿WKH￿GULYH￿￿,QVWHDG￿￿VHW￿WKH￿GULYH￿RQ￿D￿VXUIDFH￿￿VXFK￿DV￿D￿IRDP￿ SDG￿￿WKDW￿ZLOO￿VXIILFLHQWO\￿FXVKLRQ￿LW￿

Check the documentation that accompanied the drive to verify that it is config- ured for your computer system.

10-10'HOO￿3UHFLVLRQ￿￿￿￿￿'HVNWRS￿6\VWHPV￿8VHU©V￿*XLGH