Dell WorkStation 410 manual 8QSDFNHDFK6&6,GHYLFHDQGSUHSDUHLWIRULQVWDOODWLRQ

￿￿ 8QSDFN￿HDFK￿6&6,￿GHYLFH￿DQG￿SUHSDUH￿LW￿IRU￿LQVWDOODWLRQ￿￿

&$87,216￿￿*URXQG￿\RXUVHOI￿E\￿WRXFKLQJ￿DQ￿XQSDLQWHG￿PHWDO￿VXUIDFH￿ RQ￿WKH￿EDFN￿RI￿WKH￿FRPSXWHU￿￿

:KHQ￿\RX￿XQSDFN￿WKH￿GULYH￿￿GR￿QRW￿VHW￿LW￿RQ￿D￿KDUG￿VXUIDFH￿￿ZKLFK￿PD\￿ GDPDJH￿WKH￿GULYH￿￿,QVWHDG￿￿VHW￿WKH￿GULYH￿RQ￿D￿VXUIDFH￿￿VXFK￿DV￿D￿IRDP￿ SDG￿￿WKDW￿ZLOO￿VXIILFLHQWO\￿FXVKLRQ￿LW￿

Configure the device for a SCSI ID number and disable termination, if necessary. For instructions, see the documentation that came with the SCSI device as well as “SCSI Configuration Guidelines” found earlier in this section.

￿￿ ,QVWDOO￿WKH￿6&6,￿GHYLFHV￿DV￿DSSURSULDWH￿￿

‡To install a SCSI hard-disk drive, complete steps 3 through 9 of “Installing an EIDE Hard-Disk Drive in the Internal Hard-Disk Drive Bracket” found earlier in this chapter. Then continue with step 4 of this procedure.

‡To install a SCSI tape drive, CD-ROM drive, or DAT drive, complete steps 2 through 5 of “Installing a Drive in a 5.25-Inch Drive Bay” found earlier in this chapter. Then continue with step 4 of this procedure.

‡To install an external SCSI device, continue with step 4 of this procedure.

‡If you are installing a SCSI host adapter card, configure the card and install it in an empty expansion slot (see “Installing an Expansion Card” in Chapter 9.) If you attach any SCSI hard-disk drives to the host adapter card, connect the hard-disk drive access cable to the SCSI host adapter card and to the AUX LED connector on the system board (see Figure 9-1).

￿￿$WWDFK￿WKH￿6&6,￿FDEOH￿WR￿HDFK￿6&6,￿GHYLFH￿

For additional instructions on connecting SCSI devices, see “SCSI Cables” found earlier in this section.

If you are installing an internal SCSI device, firmly press the SCSI cable’s header connector onto the 50- or 68-pin connector on the back of the device.

&$87,21￿￿<RX￿PXVW￿PDWFK￿WKH￿FRORUHG￿VWULS￿RQ￿WKH￿FDEOH￿ZLWK￿SLQ￿￿￿RQ￿

WKH￿GULYH·V￿LQWHUIDFH￿FRQQHFWRU￿WR￿DYRLG￿SRVVLEOH￿GDPDJH￿WR￿\RXU￿ V\VWHP￿

The connectors on Narrow SCSI cables are keyed for proper positioning—a raised area on the outside of the header connector fits into a notch on the device con- nector. The connectors on Wide SCSI cables are shaped so that they can be attached one way only.

If you are installing an external SCSI device, connect one end of the external SCSI cable to the SCSI bus connector on the back of the device. Attach the other end of the external SCSI cable to the SCSI connector on the system back panel.

NOTE: Dell offers an external SCSI 68-pin-to-50-pin adapter kit for connecting SCSI-3 devices to the SCSI-2 connector on the Precision 410 system back panel. Contact your Dell sales representative for more information.

10-18'HOO￿3UHFLVLRQ￿￿￿￿￿'HVNWRS￿6\VWHPV￿8VHU©V￿*XLGH