Troubleshooting
If you have a problem with your camcorder, refer to this checklist. Consult your dealer or a Canon Service Center if the problem persists.
Power Source
Problem | Cause | Solution |
|
|
|
|
|
|
|
| |||
|
|
|
| |||
|
|
|
|
|
|
|
Camcorder will not turn on. | Battery pack is not correctly attached. | Attach the battery pack correctly. | 14 |
| ||
The camcorder switches off by | Power save function has been | Turn on the camcorder. | 41 |
| ||
itself. | activated. |
|
|
|
|
|
Viewfinder switches on and off. | Battery pack is exhausted. | Replace or charge the battery pack. | 14 |
| ||
Recording/Playback
Buttons will not work. | Cassette is not loaded. | Load a cassette. | 27 | ||
“ |
| ” flashes on the screen. | Condensation is detected. | See reference page. | 136 |
| |||||
|
|
|
|
|
|
“REMOVE THE CASSETTE” | Camcorder stopped operating to | Unload and reload the cassette. | 27 | ||
appears on the screen. | protect the tape. |
|
| ||
The wireless controller will not | Camcorder and wireless controller | Change the remote sensor modes. | 106 | ||
work. | are not set to the same remote |
|
| ||
|
|
| sensor mode. |
|
|
|
|
| Batteries of the wireless controller | Replace the batteries. | 26 |
|
|
| are exhausted. |
|
|
Abnormal characters appear on the | This camcorder uses a | Disconnect the power source and | – | ||
screen. The camcorder does not | microcomputer. External noise or | reconnect it after a short time. If the |
| ||
operate properly. | static electricity may cause abnormal | problem still persists, disconnect the |
| ||
|
|
| characters to appear on the screen. | power source and press the RESET |
|
|
|
|
| button with a pointed item. Pressing |
|
|
|
|
| the RESET button resets all |
|
|
|
|
| settings. |
|
Recording
The POWER dial is not in the OFF | The [LED ON/OFF] option is set to | Set the [LED ON/OFF] option to | 92 |
position but the POWER indicator | [OFF]. | [ON]. |
|
is off. |
|
|
|
Image will not appear on the | The POWER dial is not set to a | Set the POWER dial to a recording | 40 |
screen. | recording program. | program. |
|
“SET THE TIME ZONE, DATE AND | Time zone, date and time are not set, | Set the time zone, date and time. If | 39 |
TIME” appears on the screen. | or the | necessary, power the camcorder |
|
| battery is exhausted. | with the compact power adapter and |
|
|
| leave it connected with the POWER |
|
|
| dial set to OFF for at least 24 hours |
|
|
| to recharge the |
|
|
| before making the settings. |
|
Pressing the start/stop button will | Cassette is not loaded. | Load a cassette. | 27 |
not start recording. | The POWER dial is not set to a | Set the POWER dial to a recording | 40 |
| recording program. | program. |
|
| The lock lever on the carrying handle | Slide the lock lever to the left and | 41 |
| is activated. | deactivate it. |
|
Camcorder will not focus. | Autofocus does not work on that | Focus manually. | 51 |
| subject. |
|
|
| Viewfinder is not adjusted. | Adjust the viewfinder with the | 19 |
|
| dioptric adjustment lever. |
|
| Lens is dirty. | Clean the lens. | 134 |
The tally lamp will not light up. | [TALLY LAMP] is set to [OFF] in the | Set [TALLY LAMP] to [ON] or | 93 |
| menu. | [BLINK]. |
|
E 
Information | Additional |
141