Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 34-806, 36-812, 34-814, 34-801 A D B Fig, A F Fig, KG Fig, Fig. J Fig. L G S Fig

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 10

Image 10

A

Fig. 16

A

Fig. 17

4. If an adjustment is necessary, loosen two screws (F)

Fig. 17, and adjust splitter bracket (A) until it is aligned

with the inside blade flange (B) Fig. 15. Tighten two

screws (F). Loosely assemble screw and fastener plate

(C), which were removed in STEP 3.

5. Insert threaded end of support rod (G) Fig. 18,

through slot in rear of saw and into hole in rear trunnion

(H). Fasten support rod (G) to trunnion with star washer

and hex nut (J) Fig. 19. NOTE: Thread nut (J) Fig. 19, onto

threads of support rod (G) as much as possible by hand.

6.	Using a wrench to hold the hex nut (J) Fig. 19, tight-
en rod (G) Fig. 20, with a small screwdriver (K) or similar
device through the hole in the end of the rod as shown in
Figure 20.
7.	Assemble lower bracket (L) Fig. 21, to rod (G) and
loosely tighten with two 5/16-18x1" hex head screws (S)
and 5/16" lockwashers from underneath bracket (L).

KG

Fig. 20

Fig. 18

Fig. 19

Fig. 21

Page 10

Image 10

Delta 34-806, 36-812, 34-814, 34-801 instruction manual A D B Fig, A F Fig, KG Fig, Fig. J Fig. L G S Fig

Contents

Models For Parts, Service, Warranty or other AssistanceUNISAW 10 Right Tilting Arbor Saw To learn more about DELTA MACHINERY4825 Highway 45 North Jackson, TN GENERAL SAFETY RULESTechnical Service Manager Delta Machinery 2.KEEP GUARDS IN PLACE and in working orderand use them to instruct others ADDITIONAL SAFETY RULES FOR CIRCULAR SAWSSAVE THESE INSTRUCTIONS Refer to them often 5.AVOID KICKBACK byGROUNDING INSTRUCTIONS POWER CONNECTIONSMOTOR SPECIFICATIONS GROUNDED OUTLET BOX CURRENT CARRYING PRONGSMAGNETIC PUSH BUTTON CONTROLS FIVE HORSEPOWER MOTORSTHREE PHASE OPERATION EXTENSION CORDSUNISAW UNPACKING AND CLEANINGswitch only screwsASSEMBLING EXTENSION WING ASSEMBLY INSTRUCTIONSASSEMBLING BLADE TILTING MECHANISM HANDLE E A B D C Fig. F BBOX TO CABINET ASSEMBLING LVC ON/OFF SWITCHASSEMBLING LVC STARTER WING.”CAUTION DISCONNECT MACHINE FROM POWER SOURCE ASSEMBLING GPE ON/OFF SWITCHASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY EG AKG Fig A D B FigA F Fig Fig. J Fig. L G S FigP M M NLY X Z Fig P A B FigP C D Fig. E Fig. A B C Fig. A Fig ATTACHING MOTOR COVERFASTENING MOTOR CORD TO SAW FRAME ASSEMBLING DUST CHUTE ADAPTER MITER GAGE HOLDER AND WRENCH HOLDERASSEMBLING RIP FENCE HOLDER BRACKETS Fig. A B Fig. A B FigSTARTING AND STOPPING THE SAW OPERATING CONTROLS AND UNISAW ADJUSTMENTSLOCKING SWITCH IN THE “OFF” POSITION OVERLOAD PROTECTIONDISCONNECT MACHINE FROM POWER SOURCE ADJUSTING 90 AND 45 DEGREE POSITIVE STOPSADJUSTING TABLE 1.DISCONNECT MACHINE FROM POWER SOURCEMITER GAGE OPERATION AND ADJUSTMENT ADJUSTING TABLE INSERTC A B C Fig. A Fig. A C B BD Fig. Fig 1.DISCONNECT MACHINE FROM POWER SOURCE MAINTENANCEREPLACING BELTS AND ADJUSTING BELT TENSION DISCONNECT MACHINE FROM POWER SOURCECROSS-CUTTING OPERATIONSPROTECTING CAST IRON TABLE FROM RUST Fig. A C Fig. B FigA Fig USING THE FENCE AS A CUT-OFFGAGERIPPING B Fig. B Fig. A Fig. FigUSING ACCESSORY MOULDING CUTTERHEAD USING AUXILIARY WOOD FACING ON THE UNIFENCEFig. B A Fig. A Fig. Fig HEAD IN A BEVEL POSITION H G Fig. W Fig. Fig. C FigUSING ACCESSORY DADO HEAD Fig. Fig. AB C Fig. FigCONSTRUCTING A FEATHERBOARD Fig. FigNOTCHTOHELP PREVENTHAND FROMSLIPPING CONSTRUCTING A PUSH STICKPUSHSTICK CUTOFFHERETO PUSH1/4WOODBiesemeyer T-Square Table Saw Blade Guard System BLADE GUARD ACCESSORIESDeluxe Uniguard Blade Guard Catalog Listing Biesemeyer T-SquareBlade GuardPARTS, SERVICE OR WARRANTY ASSISTANCE ACCESSORIESTwo Year Limited Warranty Page CENTROS DE SERVICIO DE PORTER-CABLE DELTA PORTER-CABLE DELTA SERVICE CENTERSCANADIAN PORTER-CABLE DELTA SERVICE CENTERS también pueden estar registradas en otros países