Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 34-801, 36-812, 34-814, 34-806 instruction manual M Nl, Y X Z Fig, P M, P A B Fig

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 11

M

NL

Fig. 22

8.Assemble upper splitter bracket (M) Fig. 22, to lower bracket (L) using a 5/16-18x1" hex head screw (N) with 5/16" lockwasher and 5/16" flat washer. NOTE: Do not tighten screw (N) at this time.

9.Insert the front end of splitter (P) Fig. 23, inside the splitter mounting bracket behind splitter fastener plate and screw (C). Push splitter down as far as possible, making certain the bottom edge of splitter (P) is parallel with the table surface. Tighten screw (C). Fasten splitter and blade guard assembly (P) Fig. 24, to bracket (M) using a 5/16-18x1" hex head screw (V) and 5/16" flat washer.

10.IMPORTANT: The splitter (P) Fig. 25, features a notch

(W) cut into the top edge. Raise the front of the clear blade guard (P) Fig. 25, until the rear edge of the guard slips into notch (W) of the splitter. This notch enables the blade guard to stay in the raised position and makes changing blades easier.

11.Reassemble the saw blade, making certain the teeth are pointing down at the front of the saw table as shown in Fig. 26, and assemble the outside blade flange and arbor nut (X). With open end wrench (Y) on the flats of the arbor to keep it from turning, tighten arbor nut by turning box end wrench (Z) counterclockwise.

Y

X

Z

Fig. 26

P

C

Fig. 23

P

M

V

Fig. 24

W

P

Fig. 25

P

A

B

Fig. 27

11

Image 11

Delta 34-801, 36-812, 34-814, 34-806 instruction manual M Nl, Y X Z Fig, P M, P A B Fig

Contents

To learn more about DELTA MACHINERY For Parts, Service, Warranty or other AssistanceUNISAW 10 Right Tilting Arbor Saw Models2.KEEP GUARDS IN PLACE and in working order GENERAL SAFETY RULESTechnical Service Manager Delta Machinery 4825 Highway 45 North Jackson, TN5.AVOID KICKBACK by ADDITIONAL SAFETY RULES FOR CIRCULAR SAWSSAVE THESE INSTRUCTIONS Refer to them often and use them to instruct othersGROUNDED OUTLET BOX CURRENT CARRYING PRONGS POWER CONNECTIONSMOTOR SPECIFICATIONS GROUNDING INSTRUCTIONSEXTENSION CORDS FIVE HORSEPOWER MOTORSTHREE PHASE OPERATION MAGNETIC PUSH BUTTON CONTROLSscrews UNPACKING AND CLEANINGswitch only UNISAWE A B D C Fig. F B ASSEMBLY INSTRUCTIONSASSEMBLING BLADE TILTING MECHANISM HANDLE ASSEMBLING EXTENSION WINGWING.” ASSEMBLING LVC ON/OFF SWITCHASSEMBLING LVC STARTER BOX TO CABINETEG A ASSEMBLING GPE ON/OFF SWITCHASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY CAUTION DISCONNECT MACHINE FROM POWER SOURCEFig. J Fig. L G S Fig A D B FigA F Fig KG FigP A B Fig M NLY X Z Fig P MFASTENING MOTOR CORD TO SAW FRAME ATTACHING MOTOR COVERP C D Fig. E Fig. A B C Fig. A Fig Fig. A B Fig. A B Fig MITER GAGE HOLDER AND WRENCH HOLDERASSEMBLING RIP FENCE HOLDER BRACKETS ASSEMBLING DUST CHUTE ADAPTEROVERLOAD PROTECTION OPERATING CONTROLS AND UNISAW ADJUSTMENTSLOCKING SWITCH IN THE “OFF” POSITION STARTING AND STOPPING THE SAW1.DISCONNECT MACHINE FROM POWER SOURCE ADJUSTING 90 AND 45 DEGREE POSITIVE STOPSADJUSTING TABLE DISCONNECT MACHINE FROM POWER SOURCEC A B C Fig. A Fig. A C B BD Fig. Fig ADJUSTING TABLE INSERTMITER GAGE OPERATION AND ADJUSTMENT DISCONNECT MACHINE FROM POWER SOURCE MAINTENANCEREPLACING BELTS AND ADJUSTING BELT TENSION 1.DISCONNECT MACHINE FROM POWER SOURCEFig. A C Fig. B Fig OPERATIONSPROTECTING CAST IRON TABLE FROM RUST CROSS-CUTTINGB Fig. B Fig. A Fig. Fig USING THE FENCE AS A CUT-OFFGAGERIPPING A FigFig. B A Fig. A Fig. Fig USING AUXILIARY WOOD FACING ON THE UNIFENCEUSING ACCESSORY MOULDING CUTTERHEAD H G Fig. W Fig. Fig. C Fig HEAD IN A BEVEL POSITIONFig. Fig. AB C Fig. Fig USING ACCESSORY DADO HEADFig. Fig CONSTRUCTING A FEATHERBOARDCUTOFFHERETO PUSH1/4WOOD CONSTRUCTING A PUSH STICKPUSHSTICK NOTCHTOHELP PREVENTHAND FROMSLIPPINGCatalog Listing Biesemeyer T-SquareBlade Guard BLADE GUARD ACCESSORIESDeluxe Uniguard Blade Guard Biesemeyer T-Square Table Saw Blade Guard SystemTwo Year Limited Warranty ACCESSORIESPARTS, SERVICE OR WARRANTY ASSISTANCE Page también pueden estar registradas en otros países PORTER-CABLE DELTA SERVICE CENTERSCANADIAN PORTER-CABLE DELTA SERVICE CENTERS CENTROS DE SERVICIO DE PORTER-CABLE DELTA