Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 36-812, 34-814, 34-806, 34-801 Attaching Motor Cover, P C D Fig. E Fig. A B C Fig. A Fig

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 12

FASTENING MOTOR CORD TO SAW FRAME

BC

Fig. 28

12.Using a straight edge (A) Fig. 27, make certain the splitter (P) is aligned with the saw blade (B). Using a square (C) Figs. 28 and 29, make certain saw blade (B) Fig. 28, and splitter (P) Fig. 29, are 90 degrees to the table surface. Once you are certain the splitter is aligned to the saw blade and table, tighten all splitter mounting hardware (D) Fig. 29 and recheck alignment.

13.Holding the clear blade guard, lower the saw blade and assemble the table insert (E) Fig. 30, into the opening on the saw table.

FASTENING MOTOR CORD TO SAW FRAME

1.IMPORTANT: Turn the blade tilting handwheel counterclockwise as far as it will go until the saw blade is in the 45 degree position.

2.IMPORTANT: Turn the blade raising and lowering handwheel counterclockwise until the blade is at its lowest position.

3.Fasten motor cord (A) Fig. 31 to the saw frame cross member (B), using the cable tie (C) supplied with the saw. CAUTION: Before tightening the cable tie, make certain that cord (A) is free of any interference from the motor or saw blade at all possible positions of the motor.

4.After the cable tie is tightened, cut off excess tail of cable tie (C) Fig. 31.

ATTACHING MOTOR COVER

NOTE: IF YOU HAVE AN “LVC” (STARTER BOX) VERSION UNISAW, YOU WILL HAVE TO ATTACH TWO BOTTOM SPRING CLIPS TO THE MOTOR COVER. IF YOU HAVE AN “GPE” (STARTER BOX) VERSION UNISAW THE SPRING CLIPS ARE ALREADY ATTACHED TO THE MOTOR COVER.

1.Attach the two motor cover clips to the motor cover. Align the hole in the motor cover clip with the hole in the motor cover. Place a 13/64 flat washer onto a 10-32x1/2" screw (A), insert screw through the hole in the motor cover clip and thread screw (A) into the tapped hole in the motor cover, repeat this process for the remaining motor cover clip, Fig. 32.

P

C

D

Fig. 29

E

Fig. 30

A

B

C

Fig. 31

A

Fig. 32

12

Image 12

Delta 36-812, 34-814, 34-806 Attaching Motor Cover, P C D Fig. E Fig. A B C Fig. A Fig, Fastening Motor Cord To Saw Frame

Contents

For Parts, Service, Warranty or other Assistance UNISAW 10 Right Tilting Arbor SawModels To learn more about DELTA MACHINERYGENERAL SAFETY RULES Technical Service Manager Delta Machinery4825 Highway 45 North Jackson, TN 2.KEEP GUARDS IN PLACE and in working orderADDITIONAL SAFETY RULES FOR CIRCULAR SAWS SAVE THESE INSTRUCTIONS Refer to them oftenand use them to instruct others 5.AVOID KICKBACK byPOWER CONNECTIONS MOTOR SPECIFICATIONSGROUNDING INSTRUCTIONS GROUNDED OUTLET BOX CURRENT CARRYING PRONGSFIVE HORSEPOWER MOTORS THREE PHASE OPERATIONMAGNETIC PUSH BUTTON CONTROLS EXTENSION CORDSUNPACKING AND CLEANING switch onlyUNISAW screwsASSEMBLY INSTRUCTIONS ASSEMBLING BLADE TILTING MECHANISM HANDLEASSEMBLING EXTENSION WING E A B D C Fig. F BASSEMBLING LVC ON/OFF SWITCH ASSEMBLING LVC STARTERBOX TO CABINET WING.”ASSEMBLING GPE ON/OFF SWITCH ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLYCAUTION DISCONNECT MACHINE FROM POWER SOURCE EG AA D B Fig A F FigKG Fig Fig. J Fig. L G S FigM NL Y X Z FigP M P A B FigATTACHING MOTOR COVER P C D Fig. E Fig. A B C Fig. A FigFASTENING MOTOR CORD TO SAW FRAME MITER GAGE HOLDER AND WRENCH HOLDER ASSEMBLING RIP FENCE HOLDER BRACKETSASSEMBLING DUST CHUTE ADAPTER Fig. A B Fig. A B FigOPERATING CONTROLS AND UNISAW ADJUSTMENTS LOCKING SWITCH IN THE “OFF” POSITIONSTARTING AND STOPPING THE SAW OVERLOAD PROTECTIONADJUSTING 90 AND 45 DEGREE POSITIVE STOPS ADJUSTING TABLEDISCONNECT MACHINE FROM POWER SOURCE 1.DISCONNECT MACHINE FROM POWER SOURCEADJUSTING TABLE INSERT MITER GAGE OPERATION AND ADJUSTMENTC A B C Fig. A Fig. A C B BD Fig. Fig MAINTENANCE REPLACING BELTS AND ADJUSTING BELT TENSION1.DISCONNECT MACHINE FROM POWER SOURCE DISCONNECT MACHINE FROM POWER SOURCEOPERATIONS PROTECTING CAST IRON TABLE FROM RUSTCROSS-CUTTING Fig. A C Fig. B FigUSING THE FENCE AS A CUT-OFFGAGE RIPPINGA Fig B Fig. B Fig. A Fig. FigUSING AUXILIARY WOOD FACING ON THE UNIFENCE USING ACCESSORY MOULDING CUTTERHEADFig. B A Fig. A Fig. Fig HEAD IN A BEVEL POSITION H G Fig. W Fig. Fig. C FigUSING ACCESSORY DADO HEAD Fig. Fig. AB C Fig. FigCONSTRUCTING A FEATHERBOARD Fig. FigCONSTRUCTING A PUSH STICK PUSHSTICKNOTCHTOHELP PREVENTHAND FROMSLIPPING CUTOFFHERETO PUSH1/4WOODBLADE GUARD ACCESSORIES Deluxe Uniguard Blade GuardBiesemeyer T-Square Table Saw Blade Guard System Catalog Listing Biesemeyer T-SquareBlade GuardACCESSORIES PARTS, SERVICE OR WARRANTY ASSISTANCETwo Year Limited Warranty Page PORTER-CABLE DELTA SERVICE CENTERS CANADIAN PORTER-CABLE DELTA SERVICE CENTERSCENTROS DE SERVICIO DE PORTER-CABLE DELTA también pueden estar registradas en otros países