Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 34-814 Assembling Gpe On/Off Switch, Assembling Blade Guard And Splitter Assembly, Eg A

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 9

Fig. 11

F

D

A

Fig. 11

ASSEMBLING GPE ON/OFF SWITCH

1.The GPE on/off switch (A) Fig. 11, is shipped attached to a mounting bracket at the right side of the machine.

2.Loosely assemble switch and switch bracket (A) Fig. 12, to the inside front lip of extension table with 5/16- 18x1" flat head screw (D), 5/16" flat washer (E), and 5/16 hex nut (F) through hole (G).

3.Attach the side of switch bracket (A) Fig. 13, to the inside of extension table at the front of the saw using the 7/16-20x1-1/4" screw (C) and 7/16" flat washer. Tighten screws (C) and (D).

ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY

CAUTION: DISCONNECT MACHINE FROM POWER SOURCE.

1.Remove the table insert Fig. 14. Raise the saw arbor, by turning the locking handle on the front of the saw, counter clockwise and then turn the wheel on the front of the saw clockwise as far as it will go, and remove the saw blade from the machine by following the instructions in section “CHANGING THE SAW BLADE”.

2.The inside splitter mounting bracket (A) Fig. 15, is assembled to the inside of the saw and aligned with the inside blade flange (B) at the factory.

3.To check the alignment, remove screw and fastener plate (C) Fig. 15. Using a straight edge (D) Fig. 16, check to see if the splitter bracket (A) is aligned with the inside blade flange (B). Check both the top and bottom of bracket (A) with the top and bottom of flange (B).

EG

A

Fig. 12

D

C

A

Fig. 13

Fig. 14

C

A

B

Fig. 15

9

Image 9

Delta 34-814 Assembling Gpe On/Off Switch, Assembling Blade Guard And Splitter Assembly, Eg A, D C A, Fig. C A B Fig

Contents

UNISAW 10 Right Tilting Arbor Saw For Parts, Service, Warranty or other AssistanceModels To learn more about DELTA MACHINERYTechnical Service Manager Delta Machinery GENERAL SAFETY RULES4825 Highway 45 North Jackson, TN 2.KEEP GUARDS IN PLACE and in working orderSAVE THESE INSTRUCTIONS Refer to them often ADDITIONAL SAFETY RULES FOR CIRCULAR SAWSand use them to instruct others 5.AVOID KICKBACK byMOTOR SPECIFICATIONS POWER CONNECTIONSGROUNDING INSTRUCTIONS GROUNDED OUTLET BOX CURRENT CARRYING PRONGSTHREE PHASE OPERATION FIVE HORSEPOWER MOTORSMAGNETIC PUSH BUTTON CONTROLS EXTENSION CORDSswitch only UNPACKING AND CLEANINGUNISAW screwsASSEMBLING BLADE TILTING MECHANISM HANDLE ASSEMBLY INSTRUCTIONSASSEMBLING EXTENSION WING E A B D C Fig. F BASSEMBLING LVC STARTER ASSEMBLING LVC ON/OFF SWITCHBOX TO CABINET WING.”ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY ASSEMBLING GPE ON/OFF SWITCHCAUTION DISCONNECT MACHINE FROM POWER SOURCE EG AA F Fig A D B FigKG Fig Fig. J Fig. L G S FigY X Z Fig M NLP M P A B FigATTACHING MOTOR COVER P C D Fig. E Fig. A B C Fig. A FigFASTENING MOTOR CORD TO SAW FRAME ASSEMBLING RIP FENCE HOLDER BRACKETS MITER GAGE HOLDER AND WRENCH HOLDERASSEMBLING DUST CHUTE ADAPTER Fig. A B Fig. A B FigLOCKING SWITCH IN THE “OFF” POSITION OPERATING CONTROLS AND UNISAW ADJUSTMENTSSTARTING AND STOPPING THE SAW OVERLOAD PROTECTIONADJUSTING TABLE ADJUSTING 90 AND 45 DEGREE POSITIVE STOPSDISCONNECT MACHINE FROM POWER SOURCE 1.DISCONNECT MACHINE FROM POWER SOURCEADJUSTING TABLE INSERT MITER GAGE OPERATION AND ADJUSTMENTC A B C Fig. A Fig. A C B BD Fig. Fig REPLACING BELTS AND ADJUSTING BELT TENSION MAINTENANCE1.DISCONNECT MACHINE FROM POWER SOURCE DISCONNECT MACHINE FROM POWER SOURCEPROTECTING CAST IRON TABLE FROM RUST OPERATIONSCROSS-CUTTING Fig. A C Fig. B FigRIPPING USING THE FENCE AS A CUT-OFFGAGEA Fig B Fig. B Fig. A Fig. FigUSING AUXILIARY WOOD FACING ON THE UNIFENCE USING ACCESSORY MOULDING CUTTERHEADFig. B A Fig. A Fig. Fig H G Fig. W Fig. Fig. C Fig HEAD IN A BEVEL POSITIONFig. Fig. AB C Fig. Fig USING ACCESSORY DADO HEADFig. Fig CONSTRUCTING A FEATHERBOARDPUSHSTICK CONSTRUCTING A PUSH STICKNOTCHTOHELP PREVENTHAND FROMSLIPPING CUTOFFHERETO PUSH1/4WOODDeluxe Uniguard Blade Guard BLADE GUARD ACCESSORIESBiesemeyer T-Square Table Saw Blade Guard System Catalog Listing Biesemeyer T-SquareBlade GuardACCESSORIES PARTS, SERVICE OR WARRANTY ASSISTANCETwo Year Limited Warranty Page CANADIAN PORTER-CABLE DELTA SERVICE CENTERS PORTER-CABLE DELTA SERVICE CENTERSCENTROS DE SERVICIO DE PORTER-CABLE DELTA también pueden estar registradas en otros países