Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 36-812, 34-814, 34-806, 34-801 Adjusting Table Insert, Miter Gage Operation And Adjustment

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 16

ADJUSTING TABLE INSERT

ADJUSTING TABLE INSERT

Place a straight edge (B) across the table at both ends of the table insert as shown in Fig. 46. The table insert (A) should always be level with the table. If an adjustment is necessary, turn the adjusting screws (C), as needed, with allen wrench supplied. NOTE: THE MITER GAGE

HANDLE CAN BE USED TO STORE THE ALLEN WRENCHES WHEN NOT IN USE. REMOVE THE TOP CAP OF THE MITER GAGE HANDLE FOR THE ALLEN WRENCH STORAGE COMPARTMENT.

MITER GAGE OPERATION AND ADJUSTMENT

Insert the miter gage bar into the miter gage slot and assemble the washer and lock handle (A) Fig. 47, to the miter gage bar as shown.

The miter gage is equipped with adjustable index stops at 90 degrees and 45 degrees right and left. Adjustment to the index stops can be made by tightening or loosening the three adjusting screws (B) Fig. 48, with allen wrench supplied.

To rotate the miter gage, loosen lock knob (A) Fig. 48, and move the body of the miter gage (C), to the desired angle.

The miter gage body will stop at 90 degrees and 45 degrees both right and left. To rotate the miter gage body past these points, the stop link (D) Fig. 48, must be moved up and out of the way.

The head of the miter gage pivots on a special tapered screw (G) that fastens the head to the miter gage bar. If the miter gage head does not pivot freely, or pivots too freely, it can be adjusted by loosening set screw (H) Fig. 49, and turning the screw (G) in or out. Be certain to tighten screw (H) after adjustment is made. Your miter gage is equipped with a plate (E) Fig. 49, which fits into the T-Slot groove in the table. This allows the miter gage to be pulled off the front edge of the table without falling. This allows for a longer cut off capacity in front of the blade.

C A B

C

Fig. 46

A

Fig. 47

A

C

B

B D

Fig. 48

Fig. 49

16

Image 16

Delta 36-812, 34-814 Adjusting Table Insert, Miter Gage Operation And Adjustment, C A B C Fig. A Fig. A C B BD Fig. Fig

Contents

For Parts, Service, Warranty or other Assistance UNISAW 10 Right Tilting Arbor SawModels To learn more about DELTA MACHINERYGENERAL SAFETY RULES Technical Service Manager Delta Machinery4825 Highway 45 North Jackson, TN 2.KEEP GUARDS IN PLACE and in working orderADDITIONAL SAFETY RULES FOR CIRCULAR SAWS SAVE THESE INSTRUCTIONS Refer to them oftenand use them to instruct others 5.AVOID KICKBACK byPOWER CONNECTIONS MOTOR SPECIFICATIONSGROUNDING INSTRUCTIONS GROUNDED OUTLET BOX CURRENT CARRYING PRONGSFIVE HORSEPOWER MOTORS THREE PHASE OPERATIONMAGNETIC PUSH BUTTON CONTROLS EXTENSION CORDSUNPACKING AND CLEANING switch onlyUNISAW screwsASSEMBLY INSTRUCTIONS ASSEMBLING BLADE TILTING MECHANISM HANDLEASSEMBLING EXTENSION WING E A B D C Fig. F BASSEMBLING LVC ON/OFF SWITCH ASSEMBLING LVC STARTERBOX TO CABINET WING.”ASSEMBLING GPE ON/OFF SWITCH ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLYCAUTION DISCONNECT MACHINE FROM POWER SOURCE EG AA D B Fig A F FigKG Fig Fig. J Fig. L G S FigM NL Y X Z FigP M P A B FigP C D Fig. E Fig. A B C Fig. A Fig ATTACHING MOTOR COVERFASTENING MOTOR CORD TO SAW FRAME MITER GAGE HOLDER AND WRENCH HOLDER ASSEMBLING RIP FENCE HOLDER BRACKETSASSEMBLING DUST CHUTE ADAPTER Fig. A B Fig. A B FigOPERATING CONTROLS AND UNISAW ADJUSTMENTS LOCKING SWITCH IN THE “OFF” POSITIONSTARTING AND STOPPING THE SAW OVERLOAD PROTECTIONADJUSTING 90 AND 45 DEGREE POSITIVE STOPS ADJUSTING TABLEDISCONNECT MACHINE FROM POWER SOURCE 1.DISCONNECT MACHINE FROM POWER SOURCEMITER GAGE OPERATION AND ADJUSTMENT ADJUSTING TABLE INSERTC A B C Fig. A Fig. A C B BD Fig. Fig MAINTENANCE REPLACING BELTS AND ADJUSTING BELT TENSION1.DISCONNECT MACHINE FROM POWER SOURCE DISCONNECT MACHINE FROM POWER SOURCEOPERATIONS PROTECTING CAST IRON TABLE FROM RUSTCROSS-CUTTING Fig. A C Fig. B FigUSING THE FENCE AS A CUT-OFFGAGE RIPPINGA Fig B Fig. B Fig. A Fig. FigUSING ACCESSORY MOULDING CUTTERHEAD USING AUXILIARY WOOD FACING ON THE UNIFENCEFig. B A Fig. A Fig. Fig HEAD IN A BEVEL POSITION H G Fig. W Fig. Fig. C FigUSING ACCESSORY DADO HEAD Fig. Fig. AB C Fig. FigCONSTRUCTING A FEATHERBOARD Fig. FigCONSTRUCTING A PUSH STICK PUSHSTICKNOTCHTOHELP PREVENTHAND FROMSLIPPING CUTOFFHERETO PUSH1/4WOODBLADE GUARD ACCESSORIES Deluxe Uniguard Blade GuardBiesemeyer T-Square Table Saw Blade Guard System Catalog Listing Biesemeyer T-SquareBlade GuardPARTS, SERVICE OR WARRANTY ASSISTANCE ACCESSORIESTwo Year Limited Warranty Page PORTER-CABLE DELTA SERVICE CENTERS CANADIAN PORTER-CABLE DELTA SERVICE CENTERSCENTROS DE SERVICIO DE PORTER-CABLE DELTA también pueden estar registradas en otros países