Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 34-801 Assembly Instructions, Assembling Blade Tilting Mechanism Handle, E A B D C Fig. F B

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 7

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THE SAW IS COMPLETELY ASSEMBLED AND YOU UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.

ASSEMBLING BLADE

TILTING MECHANISM

HANDLE

1.Install fiber washer (A) Fig. 3, on the blade tilting mechanism shaft (B). Install key (C), into shaft keyway.

2.Place handwheel (D) on shaft (B) Fig. 3. Make sure the groove (E), in the handwheel lines up with the key (C).

3.Push the handwheel snugly against the fiber washer and tighten the set screw.

4.Install lock knob (F) Fig. 4, into threaded end of the shaft (B). Hand-tighten lock knob at this time.

ASSEMBLING EXTENSION WING

E

A

B

D

C

Fig. 3

F

B

NOTE: CHECK TO SEE WHAT TYPE OF STARTER BOX WAS SHIPPED WITH YOUR SAW (GPE OR LVC). A GPE STARTER HAS ROUND “ON” AND “OFF” BUTTONS. A LVC STARTER HAS RECTANGLE “ON” AND “OFF” BUTTONS.

NOTE FOR GPE STARTER BOX: When assembling the left extension wing, do not install the front screw and washer at this time, it will be installed when assembling the on/off switch.

NOTE FOR LVC STARTER BOX: If your Unisaw was shipped with an LVC starter box, the LVC “ON/OFF” switch must be removed from the left side of the Unisaw. Save the hardware that attached the LVC

Fig. 4

A

B

“ON/OFF” switch to the Unisaw because it will be used to re-attach the “ON/OFF” switch to the left extension wing in the section “ASSEMBLING LVC ON/OFF SWITCH.”

Assemble the extension wing (A) Fig. 5 , to the left side of the saw table using the three 7/16"-20x11/4" hex head screws (B) and 7/16" flat washers supplied. NOTE:

MAKE SURE FRONT EDGE OF WING IS FLUSH TO OR SLIGHTLY BEHIND THE FRONT EDGE OF THE TABLE. Use a straight edge (C) Fig. 6, to make sure the extension wing (A) is level with the saw table before tightening the screws (B) Fig. 5.

A

Fig. 5

C

Fig. 6

7

Image 7

Delta 34-801, 36-812 Assembly Instructions, Assembling Blade Tilting Mechanism Handle, Assembling Extension Wing, Fig. C

Contents

To learn more about DELTA MACHINERY For Parts, Service, Warranty or other AssistanceUNISAW 10 Right Tilting Arbor Saw Models2.KEEP GUARDS IN PLACE and in working order GENERAL SAFETY RULESTechnical Service Manager Delta Machinery 4825 Highway 45 North Jackson, TN5.AVOID KICKBACK by ADDITIONAL SAFETY RULES FOR CIRCULAR SAWSSAVE THESE INSTRUCTIONS Refer to them often and use them to instruct othersGROUNDED OUTLET BOX CURRENT CARRYING PRONGS POWER CONNECTIONSMOTOR SPECIFICATIONS GROUNDING INSTRUCTIONSEXTENSION CORDS FIVE HORSEPOWER MOTORSTHREE PHASE OPERATION MAGNETIC PUSH BUTTON CONTROLSscrews UNPACKING AND CLEANINGswitch only UNISAWE A B D C Fig. F B ASSEMBLY INSTRUCTIONSASSEMBLING BLADE TILTING MECHANISM HANDLE ASSEMBLING EXTENSION WINGWING.” ASSEMBLING LVC ON/OFF SWITCHASSEMBLING LVC STARTER BOX TO CABINETEG A ASSEMBLING GPE ON/OFF SWITCHASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY CAUTION DISCONNECT MACHINE FROM POWER SOURCEFig. J Fig. L G S Fig A D B FigA F Fig KG FigP A B Fig M NLY X Z Fig P MP C D Fig. E Fig. A B C Fig. A Fig ATTACHING MOTOR COVERFASTENING MOTOR CORD TO SAW FRAME Fig. A B Fig. A B Fig MITER GAGE HOLDER AND WRENCH HOLDERASSEMBLING RIP FENCE HOLDER BRACKETS ASSEMBLING DUST CHUTE ADAPTEROVERLOAD PROTECTION OPERATING CONTROLS AND UNISAW ADJUSTMENTSLOCKING SWITCH IN THE “OFF” POSITION STARTING AND STOPPING THE SAW1.DISCONNECT MACHINE FROM POWER SOURCE ADJUSTING 90 AND 45 DEGREE POSITIVE STOPSADJUSTING TABLE DISCONNECT MACHINE FROM POWER SOURCEMITER GAGE OPERATION AND ADJUSTMENT ADJUSTING TABLE INSERTC A B C Fig. A Fig. A C B BD Fig. Fig DISCONNECT MACHINE FROM POWER SOURCE MAINTENANCEREPLACING BELTS AND ADJUSTING BELT TENSION 1.DISCONNECT MACHINE FROM POWER SOURCEFig. A C Fig. B Fig OPERATIONSPROTECTING CAST IRON TABLE FROM RUST CROSS-CUTTINGB Fig. B Fig. A Fig. Fig USING THE FENCE AS A CUT-OFFGAGERIPPING A FigUSING ACCESSORY MOULDING CUTTERHEAD USING AUXILIARY WOOD FACING ON THE UNIFENCEFig. B A Fig. A Fig. Fig H G Fig. W Fig. Fig. C Fig HEAD IN A BEVEL POSITIONFig. Fig. AB C Fig. Fig USING ACCESSORY DADO HEADFig. Fig CONSTRUCTING A FEATHERBOARDCUTOFFHERETO PUSH1/4WOOD CONSTRUCTING A PUSH STICKPUSHSTICK NOTCHTOHELP PREVENTHAND FROMSLIPPINGCatalog Listing Biesemeyer T-SquareBlade Guard BLADE GUARD ACCESSORIESDeluxe Uniguard Blade Guard Biesemeyer T-Square Table Saw Blade Guard SystemPARTS, SERVICE OR WARRANTY ASSISTANCE ACCESSORIESTwo Year Limited Warranty Page también pueden estar registradas en otros países PORTER-CABLE DELTA SERVICE CENTERSCANADIAN PORTER-CABLE DELTA SERVICE CENTERS CENTROS DE SERVICIO DE PORTER-CABLE DELTA