Manuals / Delta / Kitchen Appliance / Waffle Iron

Delta 34-806, 36-812, 34-814, 34-801 Using Accessory Dado Head, Fig. Fig. AB C Fig. Fig

Models: 34-801 34-806 34-814 36-812

1 28

Download 28 pages 38.89 Kb

Page 22

USING ACCESSORY

USING ACCESSORY

DADO HEAD

IMPORTANT: THE BLADE GUARD AND SPLITTER ASSEMBLY CANNOT BE USED WHEN DADOING OR MOULDING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW.

Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, as shown in Fig. 69. Various combinations of saws and cutters are used to cut grooves from 1/8" to 13/16" for use in shelving, making joints, tenoning, grooving, etc. The cutters are heavily swaged and must be arranged so that this heavy portion falls in the gullets of the outside saws, as shown in Fig.

70.The saw and cutter overlap is shown in Fig. 71, (A) being the outside saw, (B) an inside cutter, and (C) a paper washer or washers which can be used as needed to control the exact width of groove. A 1/4" groove is cut by using the two outside saws. The teeth of the saws should be positioned so that the raker on one saw is beside the cutting teeth on the other saw.

The dado head set (D) Fig. 72, is assembled to the saw arbor as shown. NOTE: THE OUTSIDE ARBOR FLANGE

CAN NOT BE USED WITH THE DADO HEAD SET, TIGHTEN THE ARBOR NUT AGAINST THE DADO HEAD SET BODY. DO NOT LOOSE THE OUTSIDE ARBOR FLANGE, FOR IT WILL BE NEEDED WHEN REATTACHING A BLADE TO THE UNISAW ARBOR. ALSO, THE ACCESSORY DADO HEAD SET TABLE INSERT (E) FIG. 72, MUST BE USED IN PLACE OF THE STANDARD TABLE INSERT.

IMPORTANT: THE BLADE GUARD AND SPLITTER ASSEMBLY CANNOT BE USED WHEN DADOING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW AS EXPLAINED PREVIOUSLY IN THIS MANUAL. AUXILIARY JIGS, FIXTURES, PUSH STICKS AND FEATHER BOARDS SHOULD ALSO BE USED.

Fig. 73, shows a typical dado operation using the miter gage as a guide.

WARNING: NEVER USE THE DADO HEAD IN A BEVEL POSITION.

IMPORTANT: ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPLETED.

Fig. 72

Fig. 69

Fig. 70

AB

C

Fig. 71

Fig. 73

22

Image 22

Delta 34-806, 36-812, 34-814, 34-801 instruction manual Using Accessory Dado Head, Fig. Fig. AB C Fig. Fig

Contents

Models For Parts, Service, Warranty or other AssistanceUNISAW 10 Right Tilting Arbor Saw To learn more about DELTA MACHINERY4825 Highway 45 North Jackson, TN GENERAL SAFETY RULESTechnical Service Manager Delta Machinery 2.KEEP GUARDS IN PLACE and in working orderand use them to instruct others ADDITIONAL SAFETY RULES FOR CIRCULAR SAWSSAVE THESE INSTRUCTIONS Refer to them often 5.AVOID KICKBACK byGROUNDING INSTRUCTIONS POWER CONNECTIONSMOTOR SPECIFICATIONS GROUNDED OUTLET BOX CURRENT CARRYING PRONGSMAGNETIC PUSH BUTTON CONTROLS FIVE HORSEPOWER MOTORSTHREE PHASE OPERATION EXTENSION CORDSUNISAW UNPACKING AND CLEANINGswitch only screwsASSEMBLING EXTENSION WING ASSEMBLY INSTRUCTIONSASSEMBLING BLADE TILTING MECHANISM HANDLE E A B D C Fig. F BBOX TO CABINET ASSEMBLING LVC ON/OFF SWITCHASSEMBLING LVC STARTER WING.”CAUTION DISCONNECT MACHINE FROM POWER SOURCE ASSEMBLING GPE ON/OFF SWITCHASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY EG AKG Fig A D B FigA F Fig Fig. J Fig. L G S FigP M M NLY X Z Fig P A B FigP C D Fig. E Fig. A B C Fig. A Fig ATTACHING MOTOR COVERFASTENING MOTOR CORD TO SAW FRAME ASSEMBLING DUST CHUTE ADAPTER MITER GAGE HOLDER AND WRENCH HOLDERASSEMBLING RIP FENCE HOLDER BRACKETS Fig. A B Fig. A B FigSTARTING AND STOPPING THE SAW OPERATING CONTROLS AND UNISAW ADJUSTMENTSLOCKING SWITCH IN THE “OFF” POSITION OVERLOAD PROTECTIONDISCONNECT MACHINE FROM POWER SOURCE ADJUSTING 90 AND 45 DEGREE POSITIVE STOPSADJUSTING TABLE 1.DISCONNECT MACHINE FROM POWER SOURCEMITER GAGE OPERATION AND ADJUSTMENT ADJUSTING TABLE INSERTC A B C Fig. A Fig. A C B BD Fig. Fig 1.DISCONNECT MACHINE FROM POWER SOURCE MAINTENANCEREPLACING BELTS AND ADJUSTING BELT TENSION DISCONNECT MACHINE FROM POWER SOURCECROSS-CUTTING OPERATIONSPROTECTING CAST IRON TABLE FROM RUST Fig. A C Fig. B FigA Fig USING THE FENCE AS A CUT-OFFGAGERIPPING B Fig. B Fig. A Fig. FigUSING ACCESSORY MOULDING CUTTERHEAD USING AUXILIARY WOOD FACING ON THE UNIFENCEFig. B A Fig. A Fig. Fig HEAD IN A BEVEL POSITION H G Fig. W Fig. Fig. C FigUSING ACCESSORY DADO HEAD Fig. Fig. AB C Fig. FigCONSTRUCTING A FEATHERBOARD Fig. FigNOTCHTOHELP PREVENTHAND FROMSLIPPING CONSTRUCTING A PUSH STICKPUSHSTICK CUTOFFHERETO PUSH1/4WOODBiesemeyer T-Square Table Saw Blade Guard System BLADE GUARD ACCESSORIESDeluxe Uniguard Blade Guard Catalog Listing Biesemeyer T-SquareBlade GuardPARTS, SERVICE OR WARRANTY ASSISTANCE ACCESSORIESTwo Year Limited Warranty Page CENTROS DE SERVICIO DE PORTER-CABLE DELTA PORTER-CABLE DELTA SERVICE CENTERSCANADIAN PORTER-CABLE DELTA SERVICE CENTERS también pueden estar registradas en otros países