Delta 34-806 Unpacking And Cleaning, Unisaw, screws, Extension Wing, Handwheel, Locknob, Foreword

Models: 34-801 34-806 34-814 36-812

1 28
Download 28 pages 38.89 Kb
Page 6
Image 6
OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

FOREWORD

The Delta Unisaw is a 10" right tilting arbor saw. The Delta Unisaw features set the standards in the table saw industry.

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. NOTE: REMOVE THE STYROFOAM PACKING AND ANY OTHER ITEMS FROM THE INSIDE OF THE SAW CABINET. IMPORTANT: The saw is shipped with the saw arbor in the 45 degree position. NOTE: THE HAND

WHEEL MUST BE ASSEMBLED TO THE SAW, SEE THE SECTION “ASSEMBLING BLADE TILTING MECHANISM”, THEN PROCEED WITH THE FOLLOWING. Loosen locking knob on the handwheel, and turn handwheel until the saw arbor is in the 90 degree position and remove the styrofoam packing from inside the saw cabinet. Tighten locking knob.

UNISAW

1.Unisaw

2.Switch (shown with a LVC switch)

3.Motor cover

4.Blade guard and splitter bracket

5.Support rod

6.5/8" Internal tooth washer

7. 5/8-18 Jam nut

2

8.Upper bracket for splitter

9.Lower bracket for support rod

10.5/16" l.D. Flat washers (2)

11.5/16" l.D. Lockwashers (3)

12.5/16-18 x 1" hex head cap screws (4)

13. Arbor wrenches (2)

1

14.1/8" and 5/64" hex wrenches

15.Miter gage

16.Flat washer for miter gage handle

17.Handle for miter gage

18.Cap for miter gage handle

19.Dust chute adapter

20.#10 x 1/2" hex washer head

 

screws (8)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 1

 

 

21.

Extension Wing

 

 

 

 

 

 

 

 

 

 

27.

Handwheel

 

 

 

 

22.

Hangers for rip fence (2)

 

 

 

 

 

 

 

 

 

 

28.

Locknob

 

 

 

 

23.

5/16-18x1” Flat head screw for mounting switch (for GPE

 

 

29.

7/16-20x1¼" Hex head screw (3)

 

switch only)

 

 

 

 

 

 

 

 

 

 

30.

7/16" Flat washer (3)

 

 

24.

5/16” Flat washer for mounting switch (for GPE switch only)

31.

Fiber washer (for handwheel)

25.

5/16-18 Hex nut for mounting switch (for GPE switch only)

32.

Key (for handwheel)

 

 

26.

Cable Tie

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

22

19

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

5

28

25

 

27

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

15

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

14

 

 

18

31

9

 

 

29

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

7

 

6

11

 

 

 

 

30

 

 

 

 

 

 

 

 

 

20

 

 

 

 

 

26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 2

6

Page 6
Image 6
Delta 34-806 Unpacking And Cleaning, Unisaw, screws, Extension Wing, Handwheel, Hangers for rip fence, Locknob, Cable Tie