ENGLISH

Getting

 

 

Connecting the Speaker Cables

 

 

 

 

 

Carefully check the left (L) and right (R) channels and + (red) and –

 

 

 

 

 

Started

 

 

(black) polarities on the speakers being connected to the AVR-1909,

 

 

 

and be sure to interconnect the channels and polarities correctly.

 

 

 

 

 

 

 

 

 

 

 

 

 

Peel off about 0.03 ft/10 mm of sheathing

 

Connections

 

 

 

 

 

1from the tip of the speaker cable, then

 

 

 

 

 

 

 

 

either twist the core wire tightly or

 

 

 

 

terminate it.

 

 

 

 

 

 

 

 

 

 

 

Setup

 

 

Turnthespeakerterminal

 

 

 

2counterclockwise to loosen it.

 

 

 

 

 

Playback

 

 

3the hilt into the speaker terminal.

 

 

 

 

Insert the speaker cable’s core wire to

 

Remote

 

 

 

 

 

 

 

 

4tighten it.

 

 

 

 

 

 

Turn the speaker terminal clockwise to

 

Control

 

 

 

 

 

 

 

 

 

 

 

 

 

When using a banana plug

 

zone-Multi

 

 

Tighten the

speaker

terminal firmly

before

 

 

 

inserting the banana plug.

 

 

 

 

 

 

 

Information

 

 

 

 

 

 

 

 

 

NOTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Use speakers with an impedance of 6 to 16 Ω/ohms. When using

 

 

 

 

front A and B speakers simultaneously, use speakers with an

 

Troubleshooting

 

 

impedance of 12 to 16 Ω/ohms.

 

 

 

 

• Connect the speaker cables in such a way that they do not stick out

 

 

 

of the speaker terminals. The protection circuit may be activated if

 

 

 

 

 

 

 

 

the core wires touch the rear panel or if the + and – sides touch each

 

 

 

 

other (v “Protection circuit”).

 

 

 

 

 

• Never touch the speaker terminals while the power supply is

 

 

 

 

connected. Doing so could result in electric shock.

 

Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Protection circuit

If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will flash red at intervals of 0.5 secs.

If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please confirm that speaker cable and input cable are connected.

Also, if replaying large sound levels by using a speaker having an impedance less than that specified (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will flash red at 2 second intervals.

In this case, please switch off the power supply, and wait until the AVR-1909 has cooled down, and the surrounding ventilation is good.

Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming acti- vated, due to thinking that the AVR-1909 has failed, please contact DENON Service center after switching off.

11