ENGLISH
Getting |
|
| A4SB CH Out (for | |
| ||||
|
| Determine whether to use surround back speakers. | ||
Started |
|
| ||
|
| [Selectable items] | ||
|
|
| ||
|
|
|
|
|
|
|
| ON | : The surround back channel signal is played. |
Connections |
|
|
|
|
|
| OFF | : The surround back channel signal is not played. | |
|
|
| ||
|
|
| A5SW ATT (SUBWOOFER ATT.) | |
|
|
| Attenuate subwoofer level when using EXT. IN mode. | |
Setup |
|
| ||
|
| [Selectable items] | ||
|
|
| ||
|
|
|
|
|
Playback |
|
| ON | : The input from the subwoofer channel is attenuated. |
|
|
|
| |
|
| OFF | : The input from the subwoofer channel is not attenuated. | |
|
|
| ||
Remote |
|
|
| Usually use in this mode. |
|
| Set this to “ON” if the subwoofer channel level seems too high when | ||
Control |
|
| playing audio signal. | |
|
| A6Subwoofer | ||
|
|
| ||
|
| Turn subwoofer output on and off. | ||
|
|
| ||
zone |
|
| [Selectable items] | |
|
|
|
| |
Information |
|
| ON | : The subwoofer is used. |
|
| A7Default | ||
|
|
| OFF | : The subwoofer is not used. |
Troubleshooting |
|
|
|
|
|
| Resets the settings to the default values. | ||
|
|
| ||
Specifications |
|
|
|
|
|
|
|
|
|
Tone
Adjust the tonal quality of the sound.
A8Tone Control
Turn tone adjustments off.
[Selectable items]
ON : Allow tone adjustment (treble, bass).
OFF : Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
NOTE
When the “Dynamic EQ” setting is “ON”, setting is not possible.
A9Bass
Adjust low frequency range (bass).
[Variable range] | |
|
|
S0Treble
Adjust high frequency range (treble).
[Variable range] |
“Bass” and “Treble” can be set when “Tone Control” is set to “ON”.
Audyssey Settings
Select room equalizer for current environment.
S1MultEQ
Select the type of room correction desired from the following list:
[Selectable items]
Audyssey : Optimize frequency response of all speakers.
Audyssey Byp. L/R : Optimize frequency response of speakers except front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat response.
Manual : Apply frequency response set with “Manual EQ” (vpage 34).
|
| OFF |
|
| : Turn equalizer off. | ||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
| Audyssey |
|
| Audyssey Byp. L/R | ||||
|
|
|
|
| |||||||
|
| OFF |
|
|
| Manual |
| Audyssey Flat | |||
|
|
|
|
|
| ||||||
Operating from the main unit or main remote control unit
Press MULTEQ.
•When “Audyssey”, Audyssey Byp. L/R” or “Audyssey Flat” is
selected, “
” lights.
•After running Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “
” lights.
•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be selected after the auto setup procedure has been performed.
•After performing “Auto Setup”, the “MultEQ” setting automatically becomes “Audyssey”.
•If the settings of speakers for which “None” has been determined at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” cannot be selected. Either perform Auto Setup again, or return to the setting after running Auto Setup with “Auto Setup” – “Parameter Check” – “Restore”.
•MultEQ and Manual EQ set to “Not Used” with “Manual Setup”
– “Audio Setup” – “EQ Preset” – “EQ Customize” (vpage 34) on the menu, cannot be selected.
•When using headphones, “MultEQ” is set to “OFF”.
49For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 46).