Denon AVR-1911 NOTE, NOTE, NOTE, NOTE, NOTE, Basic, Simple, MULTEQ, Information, Audio Adjust

Setting items	Setting details
Height Gain	Low : Reduce the front height channel volume.
Control the front height	Mid : Front height channel sound is output with standard sound volume.
channel volume.	High : Increase the front height channel volume.

NOTE

	“Height Gain” is displayed for the following settings.
	• When “Amp Assign” (vpage 54) is set to “Front Height”.
	• When the “Speaker Config.” – “Front Height” setting (vpage 55) is set
	to other than “None”.
	• When surround mode is “PLgz” or the PLgz decoder is used.
Subwoofer	ON : The subwoofer is used.
Turn subwoofer output on	OFF : The subwoofer is not used.
and off.	NOTE
	This can be set when the surround mode is “DIRECT” or “PURE DIRECT”
	(vpage 72, 73), and the “Subwoofer Mode” (vpage 55) is “LFE+Main”.
Default	Yes : Reset to the defaults.
The “Surround Parameter”	No : Do not reset to the defaults.
settings are returned to the
default settings.
Tone	Default settings are underlined.

Adjust the tonal quality of the sound.

Setting items	Setting details
Tone Control	ON : Allow tone adjustment (bass, treble).

Set the tone control function OFF : Playback without tone adjustment. to ON and OFF.

“Tone Control” can be set when “Dynamic EQ” (vpage 52) is set to “OFF”.

NOTE

•“Tone Control” settings are not reflected to ZONE2.

•The tone cannot be adjusted in the direct mode.

Bass	–6dB – +6dB (0dB)
Adjust low frequency range	“Bass” can be set when “Tone Control” is set to “ON”.
(bass).
Treble	–6dB – +6dB (0dB)
Adjust high frequency range

(treble). “Treble” can be set when “Tone Control” is set to “ON”.

							ENGLISH
						Audio Adjust
Audyssey Settings								Simple
				Default settings are underlined.
Set MultEQ®, Dynamic EQ® and Dynamic Volume™. These can be selected after Audyssey® Auto Setup								version
has been performed. For additional information on Audyssey technology, please see page 76.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 10) to return to
the settings after Audyssey Auto Setup was run.								Basic
Setting items			Setting details
								version
MultEQ	Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from	Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ	front L and R speakers.
corrects both time and	Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response	response.
problems in the listening	Manual : Apply frequency response set with “Manual EQ” (vpage 53).
area based on Audyssey	OFF : Turn “MultEQ” equalizer off.
Auto Setup calibration. We
recommend “Audyssey”.	• “Audyssey”, “Audyssey		Byp.	L/R”	and
MultEQ is the prerequisite
	“Audyssey Flat” can be selected after Audyssey
function for Dynamic EQ								Advanced
	Auto Setup has been performed. “Audyssey” is
and Dynamic Volume.
	automatically selected after performing Audyssey
	Auto Setup. When “Audyssey”, “Audyssey Byp.
	L/R” or “Audyssey	Flat”	is selected,					version
	illuminates.
	• After running Audyssey Auto Setup, if the
	Speaker Configuration, Distance,			Channel
	Level, and Crossover Frequency have changed
	without increasing the number of speakers
	measured, only	illuminates.

•Pressing MULTEQ on the remote control unit or the main unit makes this setting.

NOTE

•“MultEQ” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 58).

•When using headphones, “MultEQ” is automatically set to “OFF”.

Information

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu	51
buttons	(Up/Down/Left/Right)