SAFETY INSTRUCTIONS

1.Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions – The safety and operating instructions should be retained for future reference.

3.Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions – All operating and use instructions should be followed.

5.Water and Moisture – The appliance should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.

6.Carts and Stands – The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

7.Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8.Ventilation – The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10.Power Sources – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11.Grounding or Polarization – Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

12.Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

14.Cleaning – The appliance should be cleaned only as recommended by the manufacturer.

15.Power Lines – An outdoor antenna should be located away from power lines.

16.Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

17.Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

18.Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

19.Damage Requiring Service – The appliance should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

20.Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODEANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

3

Page 3
Image 3
Denon AVR-3802 manual Safety Instructions

AVR-3802 specifications

The Denon AVR-3802 is a noteworthy feature-rich audio/video receiver that stands out in the realm of home theater systems. Released in the early 2000s, it continues to be appreciated by audiophiles and home cinema enthusiasts alike, thanks to its robust performance and advanced technologies.

One of the standout features of the AVR-3802 is its impressive power output. With a 110 watts per channel rating over 7 channels, it provides ample power to drive a variety of speakers, allowing users to create a dynamic home theater experience. This results in clear, powerful sound across a range of audio formats, from music to movies.

The AVR-3802 is equipped with a comprehensive array of inputs and outputs. It includes multiple analog and digital inputs, allowing for the connection of various audio sources such as CD players, DVD players, and gaming consoles. Additionally, the receiver supports up to seven channels of surround sound, making it compatible with numerous audio formats including Dolby Digital and DTS, which are crucial for cinematic sound experiences.

Another key feature is the incorporation of Denon's proprietary technologies, such as the "Advanced Surround Processing" which enhances the spatial audio experience. This feature helps in creating an immersive environment, utilizing different sound processing modes tailored for different content types, whether it's a concert, movie, or video game.

Denon has also ensured that the AVR-3802 displays excellent video performance. It offers multiple video inputs, including composite, S-video, and component video, facilitating high-quality video playback. The receiver supports up to 1080p video resolution, ensuring compatibility with high-definition displays. Additionally, it includes a built-in video upscaling feature that enhances lower resolution content to optimize the viewing experience.

The user interface on the AVR-3802 is designed with usability in mind. A large, easy-to-read display combined with intuitive remote control navigation simplifies the process of adjusting settings, programming presets, and switching between inputs.

In summary, the Denon AVR-3802 remains a solid choice for those seeking a high-performance audio/video receiver. With its robust power handling, versatile connectivity options, advanced surround sound processing, and high-definition video capabilities, it provides an excellent foundation for building a home entertainment system. Enthusiasts can enjoy rich, immersive audio experiences coupled with stunning video quality, making the AVR-3802 a lasting component in the world of home theaters.