ENGLISH

GAudioH

Symptom

Cause/Solution

Page

Audio is not output.

• Check the connections for all devices.

5, 12 – 16

 

• Check the speaker connections.

5, 26

 

• Check whether the audio device power is turned on.

6

 

• Adjust the master volume.

17

 

• Cancel the mute mode.

17

 

• Select a suitable input source.

17

 

• Select a suitable input mode.

32

 

• Disconnect the headphones. No sound is output from the speakers

39

 

or the PRE OUT connectors when headphones are connected.

 

No sound is

• Check if the surround speakers are connected to the SURROUND

–

produced from

terminals.

 

surround speaker.

 

 

No sound is

• Set “Speaker Config.” – “S.B(Pre)” on the menu to something

7

produced from

other than “None”.

 

surround back

• Set “Surround Parameter” – “SB CH OUT” on the menu to

35

speaker.

something other than “OFF”.

 

 

• Set the surround mode to something other than “STEREO”.

21

No sound is

• Check the subwoofer connections.

5, 26

produced from

• Turn on the subwoofer’s power.

6

subwoofer.

• Set “Speaker Config.” – “SW” on the menu to “Yes”.

7

 

• If “Front” and “Center” for “Speaker Config.” are set to “Large”,

7, 8

 

and “Mode” is set to “LFE”, no sound may be output from the

 

 

subwoofers, depending on the input signal or selected surround

 

 

mode.

 

DTS sound is not

• Set “Decode” on the menu to “Auto” or “DTS”.

32

output.

 

 

Dolby TrueHD, DTS-

• Make HDMI connections.

12

HD, Dolby Digital

 

 

Plus audio is not

 

 

output.

 

 

GHDMIH

 

 

Symptom

Cause/Solution

Page

 

 

 

No audio is

• Check the connection of the HDMI connectors.

12

output with HDMI

• When outputting HDMI audio from the speakers, set “Audio Out”

34

connection.

on the menu to “Amp”.

 

 

• When outputting HDMI audio from a TV, set “Audio Out” on the

34

 

menu to “TV”.

 

No video is

• Check the connection of the HDMI connectors.

12

output with HDMI

• Set the input source to match the connected HDMI connector.

12, 17

connection.

• Check whether the TV is compatible with copyright protection

12

 

(HDCP). If connected to a device not compatible with HDCP, video

 

 

will not be output correctly.

 

GRadioH

Symptom

Cause/Solution

Page

 

 

 

Reception fails, or

• Change the antenna orientation or position.

16

there is a lot of noise

• Separate the AM loop antenna from the unit.

16

or distortion.

• Use an FM outdoor antenna.

16

 

• Separate the antenna from other connection cables.

16

GiPodH

 

 

Symptom

Cause/Solution

Page

 

 

 

iPod cannot be

• Check the iPod connections.

16

played.

• Plug the control dock for iPod’s AC adapter into a power outlet.

–

 

• Switch the input source to “DOCK”.

17

“Connection Error”

• Unable to communicate properly. Turn off the power to this unit,

–

is displayed.

disconnect the iPod and then reconnect it.

 

“Not Support” is

• The iPod connected to the unit is not compatible. Please make

–

displayed.

sure the iPod you are connecting is compatible.

 

 

• The software version of the connected iPod is an old one. Please

–

 

update to the latest version.

 

“Connection Error”

• The iPod is not responding. Turn off the power to this unit,

–

is displayed.

disconnect the iPod and then reconnect it.

 

GRemote control unitH

 

 

Symptom

Cause/Solution

Page

 

 

 

The set cannot be

• Batteries are worn out. Replace with new batteries.

42

operated with the

• Operate the remote control unit within a distance of about 23 ft /

42

remote control unit.

7 m from this unit and at an angle of within 30°.

 

 

• Remove any obstacle between this unit and the remote control

42

 

unit.

 

 

• Insert the batteries in the proper direction, checking the q and

42

 

w marks.

 

 

• The set’s remote control sensor is exposed to strong light (direct

42

 

sunlight, inverter type fluorescent bulb light, etc.). Move the set

 

 

to a place in which the remote control sensor will not be exposed

 

 

to strong light.

 

50