Denon DN-S3000 manual Compact Discs, 0 !1

ENGLISH

(4) Display

q w	e	r	t	y	u
A1	B

TOTAL REMAIN ELAPSED		CONT. SINGLE	KEY ADJ.	DRAG S.
	m	s		BRAKE
m	s	f

MEMO			DUMP
			RVS
i	t	o	!0 !1

q Track, minute, second and frame	r Parameter indicators
displays	(upper 30 dots)
• These displays indicate current position	• Upper 30 dots on display indicate parameter,
information.	data setting for Effector.

oPlay Position indicators (lower 33 dots)

•Play position indicator:

The 33 white dots indicate where is playing visually in a track in the normal play. The 11 Orange dots indicate play position in the reverse play mode.

•End of Message:

When the time remaining to the end of the track is less than the specified time, the EOM (End Of Message) play position indicator flashes along with the remaining time, notifying of the track end.

✽ The EOM time can be set in the presets.

!0Pitch display

•This indicator display the playback speed (pitch).

!1PLATTER MODE indicators

•There are indicators for all Platter Effects DRAG-S., BRAKE, DUMP and RVS. These indicators light up when each mode is on.

4	COMPACT DISCS
1. Precautions on handling compact discs
• Do not allow fingerprints, oil or dust to get on the
	surface of the disc.
	If the disc is dirty, wipe it off with a soft dry cloth.
• Do not use benzene, thinner, water, record spray,
	electrostatic-proof chemicals, or silicone-treated
	cloths to clean discs.
• Always handle discs carefully to prevent
	damaging the surface; in particular when
	removing a disc from its case or returning it.
• Do not bend the disc.
• Do not apply heat.
• Do not enlarge the hole in the center of the disc.
•	Do not write on the label (printed side) with a
	hard-tipped implement such as a pencil or ball
	point pen.
• Condensation will form if a disc is brought into a
	warm area from a colder one, such as outdoors
	in winter. Do not attempt to dry the disc with a
	hair dryer, etc.
2. Precautions on storage
•	After playing a disc, always unload it from the

wLoop mode indicators

•DN-S3000 has Loop mode indicators which consist of A , B and two arrows. A and B marks indicate A and B points are exist.

•Two arrows indicate loop setting mode as follow.

A1	B		or	A1	B Left arrow only on:
Hot Start mode
A1	B	Both arrows on:
Seamless Loop mode
A1	B	,	A1	B	Both arrows flashing:
Seamless Loop Playing
A1	B	,	A1	B	Left arrow on, right flashing:

Exit play from Seamless Loop

eTime mode indicators

•When the TIME/T.TIME button is pushed, the Time mode indicator switches as follows:

ELAPSED:

Track’s elapsed time is displayed.

REMAIN:

Track’s remaining time is displayed.

TOTAL + ELAPSED:

The total elapsed time of disc is displayed.

TOTAL + REMAIN:

The total remaining time of disc is displayed.

tCharacter display

•You can select mode or function using PARAMETERS knob following the short message which is displayed on the character display part.

•The character display indicates the operation, mode name, data, etc., and displays such guide messages as “Yes/Push_PM” means if “YES”, push PARAMETERS knob. The display

indicates and marks sometime, note

that mark says you to turn PARAMETERS

knob and marks says to push PARAMETERS knob.

•The PARAMETERS LED flashes when you can use PARAMETER knob, otherwise this knob used for Track Selection.

yPlay mode indicators

•When SINGLE indicator lights up, playback will finish at end of current track.

•When CONT. indicator lights up, playback continues.

uKEY ADJ. indicator

•KEY ADJ. indicator appears in display when in the Key Adjust mode.

player.
• Always store the disc in the jewel case to protect
from dirt or damage.
• Do not place discs in the following areas:
(1)	Areas exposed to direct sunlight for a
	considerable time.
(2)	Areas subject to accumulation of dust or high
	humidity.
(3)	Areas affected by heat from indoor heaters,
	etc.

iMEMO indicator

•MEMO indicator appears in display when there is a memo setting for the currently playing track or the track at which the standby mode is currently set.

10