Denon DN-S3000 manual Sampler, i, !0!0 w, o y, u e, t !1, !3 !4, !6 2, !5, Adjust pitch, English

10SAMPLER

DN-S3000 has Sampler of 15 seconds length. This Sampler can also be looped and scratching during playback.

q, r,

i, !0!0 w, o y, u

e, t !1, !3 !4, !6

!2, !5

Exit and Reloop
6 u The EXIT/RELOOP button
	can be used same as
	Seamless Loop function.
Reverse Play
i	You can play the Sampled	RVS
	sound in reverse by pushing
	the RVS button. In reverse play

7mode RVS LED lights up.

•Reverse playback will take affect when you push the SAMP button after reverse mode has been turned on. To return to normal forward playback, push the RVS button once again.

Moving Sampler B point

o When the B button is

ENGLISH

Adjust pitch

The Sampler playback pitch can be adjustable.

!1Push the SAMP.PITCH button, the pitch input mode is set, PARAMETERS LED flashes and the current settings are displayed on the character display.

•Start Sampler playback.

!2Turning the PARAMETERS knob can change the pitch.

✽When pushing down and turning the

PARAMETERS knob, you can change the pitch range 10 times faster.

!3Push the SAMP.PITCH button again to turn the pitch input mode off.

Adjust sound level

The Sampler playback sound level can be adjustable.

Record in Sampler

qWhen the SAMP button is

	pushed in the standby or	SAMP.
	playing, the sound from
1	SAMP point is recorded to
	Sampler memory up to 15
	seconds.
	• The SAMP button is flashing while
	recording. When the	recording is
	completed, the button turns off and the
	corresponding SAMP B LED lights up.

Setting B point

wWhen the B button is

pushed during Sampler recording, the Sampler Loop B point is set and the loop mode turns on.

2• Recording continues for approximately 15 seconds without stopping after set B point.

•If the B point is not set, recording end point set as B point automatically. Also EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically.

Stop recording

eTo stop recording before

	recording finish	STOP
3	automatically with
	memory full, push the
	STOP button.

•The EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically.

Play Sampler sound
r Playback of the Sampler	SAMP.
sound starts when the
SAMP button is pushed after
recording has stopped.

•Sampler playback continues in looping. With setting B point, playback loop between A and B point. Without B point

4setting Sampler loops whole recorded length (about 15 seconds).

t To stop the Sampler
sound push STOP button.	STOP

	Select Sampler Loop mode
	You can select loop mode for Sampler when
	Sampler playback stop.
	Loop (default):
	Sampler playback continues with
	looping.
	(EXIT/RELOOP LED stays lit)
5	Exit: Sampler playback continues over B
	point up to recording length.
	(EXIT/RELOOP LED flashes)
	Single: Sampler playback stops at B point.
	(EXIT/RELOOP LED turned off)
	y To select loop mode, push
	EXIT/RELOOP button after
	recording and before playing.

8	pushed during Sampler
	playback, the B point moves
	to the point at which the
	button was pushed, and loop
	playback from point A starts.

	Clearing the Sampler data
	!0While pressing the RVS/(CLR) button,
	push the SAMP button to clear the
	Sampler.
9	RVS	SAMP.

•Or, by pushing the RVS/(CLR) button for approx. 1 sec, you can clear Sampler.

!4Push the SAMP.VOL button, the sound level input mode is set, PARAMETERS LED flashes and the current settings are displayed on the character display.

•Start Sampler playback.

!5Turning the PARAMETERS knob can change the sound level.

!6Push the SAMP.VOL button again to turn the sound level input mode off.

15