Denon DN-S3000 Part Names And Functions, r X-EFFECT jacks X-EFFECT IN/OUT, Top panel, Front panel

ENGLISH

3PART NAMES AND FUNCTIONS

(3) Top panel

CAUTIONS:

(1) Front panel

qDisc loading slot

•Load the disc slowly, and release it once the DN-S3000 starts grabbing the disc in.

(2) Rear panel

ePOWER button (¢ON £OFF)

• Push this button to turn power on and off.

CAUTION:

CAUTION:

•Note that there are many buttons working two different function selected by short time pushing or long pushing (1second or more). The mark indicates short time push function and

mark indicates long time push function.

•Do not forcibly try to stop the Platter when it is turning. Otherwise Platter moving mechanism may be damaged.

•If a problem with Platter rotation arises when the Platter is turning, the Platter stops turning and the pause mode is set.

CAUTIONS:

•Do not load discs when the power is turned off.

•Do not try to forcibly remove a disc once the DN-S3000 has started to grab the disc.

•Do not load more than once disc at a time or insert anything other than discs.

Otherwise loading mechanism may be damaged.

•Do not turn off the power while a disc is loading or being ejected. Otherwise loading mechanism may be damaged.

rX-EFFECT jacks (X-EFFECT IN/OUT)

•Connect this jack to the DENON mixer DN- X800 and DN-S3000 with 3.5 mm stereo mini cord.

iPlay/Pause button (13)

•This button will start or pause playback.

•Push once to start playback, once again to pause playback, and once more to resume playback.

o DISC EJECT button

• Eject disc with this button while button

illumination light. Note that if illumination is off,

!2FLIP/CLR button

•	FLIP:
	Use this to select operating mode of A button,
	from Hot Start mode and Stutter mode. FLIP
	LED lights up in Hot Start mode.
•	A CLR:
	If the A button is pushed while pushing the
	FLIP button, you can clear the A point.
	Or, by holding down just the FLIP button for

w CD drive	t Analog output jacks
	(LINE OUT)
• This Drive is field replaceable by you.	• This is unbalanced RCA output jacks.
• Optional spare drive is sold separately.	• Audio signals outputs.
	y Fader start jack
	• Use this when your mixer has Fader Start
	function with 3.5 mm stereo mini cord.
	u Digital output jack
	• Digital data is available from this jack.
	• Use 75 Ω/ohms pin cord for connection.
	• We recommend you use braided wire type
	shielded cable.
	NOTE: The playback level after analog
	conversion is set to -6dB of the usual
	level.

you cannot eject disc.(Eject lock function)

!0CUE button

•Pushing this button in play mode will force the track back to the position which playback started. While in search mode, it makes new Cue point. (Cue)

•In Cue mode, by pushing the CUE button makes a Stutter sound from the Cue point. This is called Stutter play. (Stutter)

!1Platter/Scratch Disc

Use this vinyl scratch disc for manual search, Pitch Bend and Scratch operations.

•Platter:

The Platter turns when playback of the source select Scratch mode button is in the Main or Sampler position and in play mode.

•Scratch Disc:

When the Scratch Disc is turning, Scratch playback of the source selected (Main or Sampler) starts.

NOTE: The Platter does not turn when the Scratch mode is set to the SEARCH mode. If “PLATTER TURN STOP” is selected within the presets, the Platter never turns, regardless of the Scratch mode.

However, you still may be able to scratch normally without the platter spinning.

When using the player in this mode, there will a small delay upon release of the scratch disc. (This is normal)

To avoid this delay, press the PLAY button simultaneously upon release of the scratch disc with your thumb.

more than 1 sec.

!3(SAMP) RVS/CLR button

•(SAMP)RVS:

Use this to select the sample play direction forward and reverse. When select reverse RVS LED lights up.

•(SAMP) CLR:

If the SAMP button is pushed while pushing the FLIP button, you can clear the SAMP data. Or, by holding down just the FLIP button for more than 1 sec.

!4A button

•Using this button you can create starting point for Hot Start, Seamless Loop and Stutter.

!5SAMP button

•Push this button to record or play sound of Sampler.

!6B button

•Use this to set the B point for A point of Seamless Loop.

!7(SAMP) B button

•Use this to set the Sampler loop B point.

!8EXIT/RELOOP button

•Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function.

•The LED indicates what’s going on about looping.

EXIT/RELOOP LED lit:

Seamless Loop on or playing. EXIT/RELOOP LED flashing:

Playback after exit loop.

8