Denon DN-S3000 manual 9 A/B TRIM, r, u, !1 o, !2 !0, !2 q, !3, A/B move, A/B Trim, English

ENGLISH

9A/B TRIM

•The Seamless Loop and Sampler loop A and B points can be fine-adjusted using the Scratch Disc.

•There are two ways for doing this.

A-B Trim: Trim the points during loop playback as a rehearsal.

A/B Move: Move the points using the fast search or manual search. A/B Move can not be used with Sampler loop.

e, t, y, i,

r, u, !1 o, !2 !0, !2 q, !3

Select B point (in A-B Trim)

	y Select the A-B Trim mode
5	and to select the B point,
	push the B button after
	selecting the A point.
	Then push the B button. The B LED flashes
	and the B point trim become enable.

Trim B point

u Turn Scratch Disc to move the B point 1 frame at a time.

•Range for trimming B point is limited as

A/B move

•A/B Move can not be used with Sampler loop.

Select A and B points
o Select or the A/B Move and	A
push the A button for the A
point you want to move. The
standby mode is set at the A
point and the A button

8illumination flashes.

!0To select the B point, push the B button after selecting the A point.

A/B Trim

Select A-B trim mode

First select whether to adjust the A and B points using the A-B trim mode or the A/B move mode.

q Push the A/B TRIM button			A/B TRIM
1	to set the A and B point
	position adjustment mode.
w	Now turn the	PARAMETERS
			PUSH
	PARAMETERS knob to		ON / OFF
	select the A-B Trim or
	the A/B Move.

Select A point (in A-B Trim)

	e Select the A-B Trim and push	A
2	the A button for the loop to
	be trimmed. The A button
	illumination flashes and loop
	playback starts.

w

Trim A point

r Turn the Scratch Disc to move the A point 1 frame at a time.

•Range for trimming A point is limited as

follows.

A point for Loop:

3±30 frames from the original A point. (However, when the A point was

loaded from the standby mode, the A point cannot be moved backwards. So, use A/B Move function)

A point for Sampler:

Between the original A point and 5 frames before B point.

Save the A point
t	Push the A button again to	A
4	save new A point, and the
	unit automatically exit from
	the A-B Trim mode.

6follows.

B point for Loop:

Between 5 frames after A point and disc end.

B point for Sampler:

Between 5 frames after A point and Sampler end.

	Save the B point
7	i Push the B button again to
	save new B point, and the
	unit automatically exit from
	finish the A-B Trim mode.

•The B LED flashes. The Selected B point is used for the A point that was first selected.

Move A or B points

!1Turn the Scratch Disc to move the selected point using the manual search function.

•Range for moving A point is limited as follows.

9A point for Loop:

Between the beginning of the disc and 5 frames before B point.

•Range for moving B point is limited as follows.

B point for Loop:

Between 5 frames after A point and disc end.

	Save the A or B points
	!2Push the A or B button
10	again. The LED stops
	flashing and the A or B point
	is saved, and the unit
	automatically exit from the
	A/B Move mode.

	Cancel the A-B Trim or A/B Move
11	!3Push the A/B TRIM button	A/B TRIM
	to cancel the mode.

14