2002 Dimension One Spas Export Owner’s Manual

 

 

 

 

 

 

 

 

 

 

 

 

Control

 

Function

 

 

3

 

3. LIGHT Pad and Status Light Push the LIGHT pad once to activate the

 

 

 

 

brightest setting (Status Light will illuminate, 1). A second push will activate the

 

 

 

 

medium setting and a third push will activate the dimmest setting. Push the

 

 

 

 

LIGHT pad a fourth time to turn off the light. The light will automatically turn

 

 

 

 

off after one hour.

 

 

 

 

NOTE: If the Dynamic L.E.D. Light is installed, the low, medium, and high

 

 

 

 

settings are disabled. The Light pad turns the Dynamic L.E.D. Light on and off.

 

 

 

 

 

 

 

4

 

4.TEMPERATURE Pads

 

 

 

 

Pushing the UP (+) pad increases the temperature and pushing the DOWN (-)

 

 

 

 

pad decreases the temperature. Push the respective pad one time for each

 

 

 

 

degree of temperature change, or push and hold the pad for rapid adjustment.

 

 

 

 

The actual hot tub water temperature will remain in the Digital Display

 

 

 

 

window until a temperature pad is pushed. When the UP or DOWN pad is

 

 

 

 

pushed the Digital Display will indicate the new temperature setting, with the

 

 

 

 

SET POINT Icon on the right side of the Digital Display. Once the new

 

 

 

 

temperature is set, the actual hot tub water temperature will again be

 

 

 

 

indicated. The hot tub will heat to the pre-set temperature automatically.

 

 

 

 

 

 

 

5

 

5. PROGRAM Pad

 

 

 

 

The PROGRAM pad is used for several different functions including: Clock Set,

 

 

 

 

Filter Cycle Start Time, Filter Cycle Duration, Number of Filter Cycles, and

 

 

 

 

Temperature Unit Selection. The paragraphs following this table will explain

 

 

 

 

how these features are set.

 

 

 

 

To initiate the programming sequence at any time, push and hold the

 

 

 

 

PROGRAM pad for 3 seconds. If, within 60 seconds, you do not proceed with

 

 

 

 

the hot tub programming, the hot tub will automatically exit the programming

 

 

 

 

sequence and revert to the previous settings. To exit the programming

 

 

 

 

sequence at any time, do not press any pad for 10 seconds. Any programming

 

 

 

 

changes made up to that point will be saved.

 

 

 

 

 

 

 

6

 

6. Dimension One Spas ICON (Logo)

 

 

 

 

The time of day can be viewed by pushing the Dimension One Spas ICON logo

 

 

 

 

on the far right of the control. If no other pad is pushed within 5 seconds, the

 

 

 

 

display will revert to the hot tub water temperature reading. The pre-set

 

 

 

 

factory default is Fahrenheit.

 

 

 

 

Pressing the logo for 5 seconds will place the spa in the “Standby” mode and

 

 

 

 

allow the spa to be cleaned without turning off the power.

 

 

 

 

 

 

 

7

 

7. Heat Status Light

 

 

 

 

This Light is illuminated whenever the heater is on.

 

 

 

 

 

 

8

Page 12
Image 12
Dimension One Spas Dynamic Massage Sequencer manual Temperature Pads, Program Pad, Dimension One Spas Icon Logo