APPLIANCE MAINTENANCE

Removing Pilot/Thermocouple From Main Burner Assembly Attention: The thermocouple CAN NOT be replaced as an individual item. You must order a new pilot when replacing thermocouple.

1.Turn OFF gas supply to the heater.

2.Turn OFF electrical supply to the heater if optional blower is installed in heater.

3.Remove lower louver from casing assembly (2 screws).

4.Remove reflector from casing assembly (2 screws).

5.Disconnect pilot tubing from pilot (see Figure 18, Page 15). Grasp nut A with a wrench when removing nut B with a second wrench.

6.Remove pilot from pilot bracket (2 screws).

7.Remove thermocouple lead from gas valve.

8.As parts are being replaced in reverse order, check for gas leaks at all gas connections before lower louver is replaced onto casing assembly.

Removing Main Burner Orifice(s) From

Main Burner Assembly

1.Turn OFF gas supply to the heater.

2.Turn OFF electrical supply to the heater if optional blower is installed in heater.

3.Remove lower louver from casing assembly (2 screws).

4.Remove reflector from casing assembly (2 screws).

5.Remove pilot bracket from main burner assembly (2 screws).

6.Pivot pilot bracket with attached pilot away from main burner assembly (do not damage pilot tubing).

7.Disconnect supply tubing from orifice holder(s).

8.Remove orifice holder from venturi of main burner assembly (1 screw for each orifice holder).

9.Remove main burner orifice from orifice holder.Attention: The number stamped on the main burner orifice is a millimeter diameter.

10. As parts are being replaced in reverse order, check for gas leaks at all gas connections before lower louver is replaced onto casing assembly.

Removing Manual Gas Control From Casing Assembly

1.Turn OFF gas supply to the heater.

2.Turn OFF electrical supply to the heater if optional blower is installed in heater.

3.Remove lower louver from casing assembly (2 screws).

4.Remove reflector from casing assembly (2 screws).

5.Disconnect inlet supply tubing, outlet supply tubing, pilot supply tubing and thermocouple lead from manual gas control.

6.If heater is attached to wall, disconnect gas supply line from inlet regulator.

7.Remove heater from wall.

8.Remove cotter pin from manual gas control rod.

9.Remove manual gas control bracket from casing assembly (3 screws

to be removed are located on casing assembly back).

10. Loosen nut that secures manual gas control to bracket. Remove manual gas control from bracket.

11.As parts are being replaced in reverse order, check for gas leaks at all gas connections before reflector and lower louver are replaced onto casing assembly.

Removing Main Burner From Casing Assembly

1.Turn OFF gas supply to the heater.

2.Turn OFF electrical supply to the heater if optional blower is installed in heater.

3.Remove lower louver from casing assembly (2 screws).

4.Remove reflector from casing assembly (2 screws).

5.Disconnect supply tubing from orifice holder(s).

6.Remove pilot bracket from main burner assembly (2 screws).

7.Remove main burner assembly from casing assembly (4 screws).

8.Remove orifice shield from main burner assembly.Attach orifice shield to new main burner assembly.

9.As parts are being replaced in reverse order, check for gas leaks at all gas connections before lower louver is replaced onto casing assembly.

Piezo Pilot Ignitor Instructions

Depressing the ignitor button completely causes a spark to occur at the pilot.

To light the pilot, it is important that the electrode be 1/8" (3mm) from the pilot. The spark must occur at the point the pilot flame hits the thermocouple.

On a new installation with air in the gas line, it is suggested that a match be used. The match will light the pilot faster than the piezo under this condition.

TROUBLESHOOTING

1.Spark electrode does not produce spark.

a.Spark electrode broken - replace.

b.Ignitor wire may not be attached to spark electrode - attach.

c.Ignitor wire damaged - replace.

d.Piezo ignitor defective - replace.

2.Spark electrode produces spark but pilot does not light.

a.No gas to heater - turn on gas.

b.PILOT position not properly aligned - turn gas control knob to PILOT position and depress.

c.Pilot is blocked from spider web or dirt - clean pilot, see Page 15.

3.Pilot flame does not stay "ON" when control knob is released.

a.Control knob in PILOT position not completely depressed or held in long enough.

b.Thermocouple not tightened into gas control - tighten thermocouple.

c.Pilot flame not surrounding thermocouple - clean pilot, see Page 15.

d.Inlet gas pressure too low, contact gas supplier.

e.Thermocouple defective - replace.

f.Gas control defective - replace.

4.Main burner does not ignite.

a.Main burner orifice is blocked - clean, see "Main Burner Flame Characteristics," Page 14. Attention: The number stamped on the main burner orifice is a millimeter diameter.

b.Inlet gas pressure too low, contact gas supplier.

5.Heater keeps shutting "OFF" during normal operation.

a.Pilot is blocked - clean pilot, see Page 15.

b.Inlet gas pressure too low, contact gas supplier

Page 16

16942-5-0907

Page 16
Image 16
Empire Comfort Systems SR-30 installation instructions Appliance Maintenance, Troubleshooting

SR-30 specifications

Empire Comfort Systems has established itself as a leading manufacturer of heating appliances, and the SR-30 gas stove is a testament to its dedication to quality and efficiency. This model is designed to seamlessly blend comfort with modern aesthetic appeal, making it an ideal choice for various living spaces.

The Empire SR-30 boasts a compact design that measures 30 inches in height, making it suitable for both small and larger rooms. One of its main features is the ability to provide heat without the need for electricity, thanks to its reliable gas-burning technology. This characteristic ensures that the stove can function during power outages, providing peace of mind and warmth even in unpredictable weather conditions.

Equipped with state-of-the-art burner technology, the SR-30 delivers an impressive heat output, ranging between 20,000 and 30,000 BTUs, capable of effectively warming spaces up to 1,200 square feet. The unit is designed with a built-in thermostat and adjustable flame control, allowing users to customize the heat output according to their comfort preferences.

Safety is a priority with the SR-30, which features a safety shut-off system designed to prevent gas leaks and ensure safe operation. The unit is also equipped with a venting system that promotes effective heat distribution while minimizing draft issues, providing a consistent and cozy warmth throughout the room.

The aesthetic design of the SR-30 is another standout feature. With a range of attractive finishes and an array of customizable options, consumers can choose a style that complements their home décor. The large glass viewing area offers a warm, flickering flame, creating an inviting atmosphere that enhances any space.

In terms of installation, the SR-30 is versatile, as it can be direct-vented or installed using a one-pipe venting system, providing options for various home configurations. Additionally, the unit operates quietly, ensuring it will not disrupt conversations or relaxation.

In conclusion, the Empire Comfort Systems SR-30 gas stove is an excellent choice for homeowners seeking an efficient, reliable, and stylish heating solution. With its powerful heating capabilities, safety features, and elegant design, the SR-30 adds warmth and charm to any living environment.