Rmt Bridge Id, Rmt IP Address | Enterasys Networks ENTERASYS ATX

Using ATX Trunking

•helddown — trunking is enabled, but the trunk connection has been rejected. Indicates that an error has been detected and the link is being held out of service until the error condition clears. After a short time-out period, another attempt will be automatically initiated to establish a good trunk connection.

•broken — the port has been conﬁgured for trunking, but is physically non- operational.

Rmt Bridge Id

Displays the MAC address portion of the remote bridge’s bridge ID.

NOTE

The Rmt Bridge Id ﬁeld can be used to determine which ports belong to which trunk group. Ports in the same trunk group will have the same remote bridge ID.

Rmt IP Address

Displays the remote bridge’s IP address.

Last Error

Displays the reason for failure when the link is in a helddown state. Reasons for failure include:

•(1) none — no error; the trunking protocol may restart with no error conditions when trunking is activated for a port or when the MIB variable that controls extra trunk groups is modiﬁed.

•(2) in-bpdu— a spanning tree BPDU was received, indicating that the connection is not point-to-point, or that the far end of the link does not have trunking enabled.

•(3) multiple-bridges— a different bridge has been connected at the far end of the link, and the trunking protocol will restart.

•(4) ack-lost(acknowledgment lost) — the far end of the link has detected a problem, and the trunking protocol will restart.

•(5) standby — the trunk group is ﬁlled to capacity with other ports; this port is now a hot standby. If another port leaves the trunk group, this port will then be included in the group.

•(6) too-many-groups— the maximum number of groups (4) has been reached, and a new group cannot be added. This port will not be used until the condition clears.

•(7) no-ack(no acknowledgment) — this port has not received a valid trunking packet, and the trunking protocol will restart.

•(8) perturbed-threshold— errors are preventing stabilization, and the trunking protocol will restart.

The Port Trunking Window

3-3

Image 47

Enterasys Networks ENTERASYS ATX manual Rmt Bridge Id, Rmt IP Address, Last Error

Contents

ATX User’s Guide Page Virus Disclaimer Page Restricted Rights Notice Page Contents Chapter ATX Port Mirroring Chapter Using ATX TrunkingChapter Using ATX Port Filtering Chapter Workgroup Conﬁguration Introduction Related Manuals Using the ATX Switch User’s Guide Software Conventions Common ATX Switch Window Fields Using Window Buttons Getting Help from the Global Technical Assistance Center Using On-line HelpGetting Help Login ATX Switch Chassis View Viewing Chassis Information ATX Switch Chassis View Port Status Front Panel InformationConnection Status Firmware Boot PromMenu Structure Port Status Menu Device Menu PPE Module Menu Utilities MenuHelp Menu Port Menu Port Status DisplaysModule Menu PPE Port Menu Status Selecting a Port Status View Port Status Color Codes Viewing Hardware Types Chassis Manager Window Interface Description Module Type Text Boxes IPX Routing Managing the Hub Selecting the Frame Type for a Port Conﬁguring IPX Routing on a port IP Conﬁg/Routing window IP Routing Conﬁguring IP Routing on a Port Conﬁguring the IP Address TableIndex Port IP Mask Broadcast Protection Port Conﬁguration Ring Speed Local SwitchingBridge Port Conﬁguration 11. Bridge Conﬁguration window Setting the Bridge Mode Bridge Number Transmitting BPDUsSource Route Conﬁguration Ring Number Token Ring Translation Setting the Spanning Tree Explorer Mode ARP Translate IPX FramingIPX Source Route To set the Token Ring Translation Parameters Netbios Source RouteARP Source Route Viewing I/F Summary Information Using the Find Source Address Feature Logical Status Index Raw Counts Interface Performance Statistics/Bar Graphs Viewing Interface Detail Rate Non-Unicast DescriptionAddress Unicast Making Sense of Detail Statistics Enabling and Disabling Ports Administratively Enabling and Disabling Ports ATX Switch Chassis View Managing the Hub Using ATX Trunking State Port Trunking Window Rmt IP Address Last ErrorRmt Bridge Id Last Change Enabling and Disabling TrunkingLink Ordinal Link Count Using ATX Trunking Using ATX Trunking Port Trunking Window Using ATX Port Filtering Using ATX Port Filtering Protocol Port Filters Table InformationId Identiﬁer Pseudo Editing the Port Filters Table Adding a New Filter Using ATX Port Filtering Using ATX Port Filtering Using ATX Port Filtering Using ATX Port Filtering Packets Viewing Filter StatisticsDeleting a Port Filter Last Frame Address Workgroup Conﬁguration Workgroup Conﬁguration Virtual Workgroups Window Total Conﬁguring a Workgroup Deleting a Workgroup Workgroup Conﬁguration Conﬁguring a Workgroup ATX Port Mirroring ATX Port Mirroring Port Mirroring Window Conﬁguring Port Mirroring If the ports being mirrored are remote From the device where the mirrored ports are located From the device where the diagnostic port is located ATX Port Mirroring Port Mirroring Window IPX Routing Tables IPX Network IPX StatisticsIPX Interface Port# IPX Route Tick Count Hop CountNext Hop Age Socket NodeID IPX Routing Tables Index Index-2 Index-3 Index Index-4