Installing an SFP Transceiver | Enterasys Networks V2H124-24P

Installing an SFP Transceiver 3

2.Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

Installing an SFP Transceiver

1	22
1
		23	24
			24

23
	Link/A
	ct P
		WR
24	PoE	Diag
24		Diag
	25
	26	Stacking
		Stacking

PMode oE/Link

V2H124-24P

Figure 3-5. Installing an SFP Transceiver

To install an SFP transceiver, perform the following steps:

1.Consider your network and cabling requirements to select an appropriate SFP transceiver type.

2.Insert the transceiver with the optical connector facing outward and the slot connector facing down. Note that SFP transceivers are keyed so they can only be installed in one orientation.

3.Slide the SFP transceiver into the slot until it clicks into place.

Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

3-5

Image 39

Enterasys Networks V2H124-24P manual Installing an SFP Transceiver

Contents

Matrix V-Series V2H124-24P Fast Ethernet Switch Page Page Regulatory Compliance Information Environmental Requirements Safety Compliance Power Cord Set France et Pérou uniquement Vii Declaration of Conformity Enterasys Networks, Inc Firmware License Aggreement Page Page Xii Contents Appendix C Specifications C-1 Glossary Index Tables Figures Figures Switch Architecture IntroductionOverview Network Management Options Power-over-Ethernet Capability Port and System Status LEDs Description of Hardware10/100BASE-T Ports 1000BASE-T/SFP Ports System Status LEDs System Status LEDs Stack Master Button Mode PoE/Link Button Optional Stacking Transceiver Power Supply Receptacle Management Features and BenefitsConnectivity Performance Network Planning Introduction to Switching Collapsed Backbone Application Examples Network Aggregation Plan Network Aggregation Plan Remote Connections with Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections Application Notes Installing the Switch Selecting a SiteEthernet Cabling Equipment Checklist Package ContentsGetting Help Mounting Optional Rack-Mounting EquipmentRack Mounting Desktop or Shelf Mounting Installing the Switch in a Rack Installing an SFP Transceiver Installing an SFP Transceiver Installing a Stacking Transceiver Stacking Switches Connecting Switches in a Stack Connecting Switches in a Stack Connecting to the Console Port Connecting to a Power Source DTE Port Wiring Map for Serial Cable Installing the Switch Twisted-Pair Devices Connecting Network DevicesPower-over-Ethernet Connections Making Network Connections Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Network Wiring Connections Network Wiring Connections Making Fiber Port Connections Fiber Optic Devices Connectivity Rules 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Domain Cable Labeling and Connection Records Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems Installation In-Band AccessStack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10/100BASE-TX Pin Assignments Crossover Wiring Straight-Through Wiring Twisted-Pair Cable and Pin Assignments B 1000BASE-T Pin Assignments Fiber Standards Cable Testing for Existing Category 5 Cable Physical Characteristics Appendix C Specifications Management Features Switch Features Compliances Standards Specifications 10BASE-T Glossary Ieee LED Virtual LAN Vlan Numerics Index Index-2 Page ES3526-PoE-60 P/N 150200039300A E042004-R01