Manuals / Enviro / Household Appliance / Stove

Enviro Cara owner manual Installation Data Sheet, OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

Models: Cara

1 44

Download 44 pages 34.11 Kb

Page 44

Installation Data Sheet

Installation Data Sheet

The following information must be recorded by the installer for warranty purposes and future reference.

NAME OF OWNER:

_________________________________________

ADDRESS:

_________________________________________

_________________________________________

_________________________________________

PHONE:___________________________________

MODEL:___________________________________

SERIAL NUMBER:___________________________

DATE OF PURCHASE: _____________ (dd/mm/yyyy)

DATE OF INSTALLATION:___________(dd/mm/yyyy)

� NATURAL GAS (NAT) � PROPANE (LPG)

INLET GAS PRESSURE:_________in wc

MAIN BURNER ORIFICE:__________# DMS

PILOT ORIFICE #_________OR________in diam.

INSTALLER’S SIGNATURE:

_________________________________________

NAME OF DEALER:

_________________________________________

ADDRESS:

_________________________________________

_________________________________________

_________________________________________

PHONE:___________________________________

NAME OF INSTALLER:

_________________________________________

ADDRESS:

_________________________________________

_________________________________________

_________________________________________

PHONE:___________________________________

MANUFACTURED BY:

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

www.envirofire.biz

October 15, 2007

C-11436

44

Image 44

Enviro Cara owner manual Installation Data Sheet, OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

Contents

INSTALLER Do not touch any electrical switch or use any phone in your buildingWHAT TO DO IF YOU SMELL GAS CONSUMERGENERAL Safety PrecautionsFOR YOUR SAFETY Table of Contents Safety PrecautionsSpecifications Blower SpeedCertified for installation from 0-4500 ft 0-1372 m Certified for installation from 0-4500 ft 0-1372 m with 36” 915 mmCodes And Approvals TOP VENT DVSpecifications Figure 1 Cara Exterior DimensionsOperating Instructions RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFEFigure 3 Pilot Assembly FOR YOUR SAFETY READ BEFORE OPERATINGFor Your Safety, Read Safety Precautions And Lighting Instructions Before OperatingOperating Instructions CaraComponent Sound & ReasonFor Your Safety, Read Safety Precautions Operating InstructionsMaintenance And Service Maintenance And Service IMPORTANT Ensure the unit is off and at room temperatureFigure 8 Install the Log Set Burner to the Firebox Figure 9 Install the Rock Set Burner to the FireboxMaintenance And Service Figure 10 Align Log Set Burner With FireboxFigure 11 Align Rock Set Burner With Firebox Figure 12 Firebox Baffle Screws RemovalTO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installingKit Parts List Conversion Kit InstallationMaintenance And Service 7. Convert the SIT gas valveInitial Installation QUALIFIED INSTALLERS ONLYInitial Installation QUALIFIED INSTALLERS ONLYFigure 24 Common Horizontal Installation Figure 25 Common Vertical InstallationManufacturer Trade NameNominal Sizes Initial InstallationInitial Installation QUALIFIED INSTALLERS ONLYDirect Vent GS Direct-TempNOTE Venting terminals shall not be recessed into walls or siding Initial InstallationQUALIFIED INSTALLERS ONLY Figure 28 Vent Termination Restrictions, refer to TableVent FeetUnitof Initial Installation4. Re-install the firebox baffle and the door Initial InstallationQUALIFIED INSTALLERS ONLY QUALIFIED INSTALLERS ONLY 2” 51mm at top, 11⁄2” 38mm at sides, 11⁄2” 38mm at bottomInitial Installation f Maintain manufacturer’s clearances to combustibles with venting Initial InstallationQUALIFIED INSTALLERS ONLY 5. Cut hole in the roof centered on the small Initial InstallationQUALIFIED INSTALLERS ONLY 10. Twist-lock the vent cap Initial InstallationQUALIFIED INSTALLERS ONLY 1. Follow installation steps 1 & 2 under INITIAL Initial InstallationQUALIFIED INSTALLERS ONLY Do not interfere with the structural integrity of the walls Initial InstallationQUALIFIED INSTALLERS ONLY to a rear vented unit for use with a 36” Initial InstallationQUALIFIED INSTALLERS ONLY Seal around the termination using a non-hardening mastic Initial InstallationQUALIFIED INSTALLERS ONLY Venturi Setting GAS LINE CONNECTIONTO TEST VALVE PRESSURES Natural GasWire Size ELECTRICAL INFORMATION Canadian InstallationsU.S.A. Installations Max. LengthInitial Installation 3. Install the temperature sensor into the holderSecondary Installation NOTE The logs are fragile and should be handled gentlySecondary Installation Figure 56 Log Placement of Left LogFigure 57 Log Placement of Center Log Figure 58 Log Placement CompleteCAUTION NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED Secondary Installation3. The four 4 large rocks are placed across front Secondary InstallationCAUTION NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED Do not install when the unit is hot Secondary InstallationFigure 65 Steel Firebox Liners Installation Figure 66 Firebox Liners InstallationTrouble Shooting ProblemSolution Possible CauseParts List ReferencePart Description PartParts List ReferencePart Description PartParts Diagram Warranty Limited Lifetime WarrantyLimited Two 2 Year Warranty Limited One 1 Year WarrantyWarranty 12. The Limited Warranty is void ifWarranty 22. Any statement or representation of VistaFlame products and their performance contained in VistaFlame advertising, packaging literature, or printed material is not part of the Limited WarrantyInstallation Data Sheet 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3