Manuals / Brands / Computer Equipment / Projector / Epson / Computer Equipment / Projector

Epson EMP-TW1000 U Replacing the lamp, Replacing the air filter, Resetting the lamp operating time

1 64

Download 64 pages, 3.48 Mb

Maintenance

Replacing consumables

Replacing the air filter

Dispose of used air

filters properly in TIP accordance with

your local regulations. Air Filter: Polypropylene

Press	or to turn	Remove the air filter
the power off, wait until		cover.

the projector cools down, and then turn off the main power switch.

Put your finger under the latch and pull it upward.

Replacing the lamp

If the lamp stops working and needs to be replaced, there is the danger that the lamp may already be broken. If replacing the lamp of a projector which has been installed to the ceiling, you should always assume that the lamp is broken and handle it with extreme care during removal. Furthermore, you should stand to the side of the projector, not underneath it.

Press or to turn the power off, wait until the projector cools down, and then turn off the main power switch.

*Wait until the lamp cools down (takes approximately 1 hour).

Securely tighten the lamp fixing screws.

Remove the lamp cover.

Install the lamp cover.

Resetting the lamp operating time

The lamp operating time must always be reset after the lamp has been replaced with a new one.

The projector has a built-in counter which keeps track of the lamp operating time. When the cumulative operating time reaches a certain point, it causes the replacement warning message to be displayed.

Press to turn on the power.

Press to display the configuration menu.

46

Contents

Page About the Manuals and Notations Used Checking the Components Table of Contents ■ Problem Solving ■ Maintenance ■ Optional Accessories / Consumables ■ List of Supported Monitor Displays ■ Specifications Features of the Projector Page Part Names and Functions Page • [SCART] input port p.12 •[Component] input port p.12 • [Trigger out] port • [Video] input port Appearance Setting up Lens shift adjustment Projection methods Connecting Image Sources Preparing the Remote Control Using the remote control Remove the lens cover Turn the power on Connect the powercable Turn on the main power switch Turn the power on for the connected equipment When the expected images are not projected Turning the power off Adjusting the Projection Screen Focus adjustment Fine adjustments to image size (Zoom adjustment) Projection imageFinepositionadjustments(Lensto imageshift) size (Zoom Correcting projector tilt Displaying a test pattern Basic Image Quality Adjustments Select Menu Operations Image Quality Adjustments Advanced Colour Adjustments Adjusting from the gamma correction values Customized ("Adjust it from the image") ("Adjust it from the graph") Offset Gain Hue Saturation Examining Image Quality Further Page Save Memory Load Memory Erase Memory Configuration Menu Functions Displaying a menu Selecting a menu item Changing settings When setting is complete Page Resolution Sync Info Color Mode *1 Brightness *2 Contrast *2 Color Saturation *2 Tint *2 Brightness Control *2 Auto Iris *3 Aspect *1 Zoom Size *1 Zoom Caption Pos. *1 Progressive*1 Motion Detection *1 Noise Reduction *1 Output Scaling *1 Setup Level *1 HDMI Video Range*1 Direct Power On Sleep Mode Child Lock Operation Lock Projection Display Input Signal Language Reset All Reset Memory Reset Lamp Hours Problem Solving warning/problem normal Problems relating to images ■No images appear Have you pressed the [Power] button Is the main power switch ■The message "Not Supported" is displayed ■The message "No Signal" is displayed ■Images are fuzzy or out of focus ■Interference or distortion appear in images ■Image is truncated (large) or small ■Image colours are not right ■Images appear dark ■Projection stops automatically Problems when projection starts ■ Power does not turn on Problems with the remote control ■The remote control does not work Maintenance Air filter replacement period Lamp replacement period Appendix Replacing the air filter Replacing the lamp Resetting the lamp operating time Page Optional Accessories / Consumables List of Supported Monitor Displays Computer image (analog RGB) Input signal from the [HDMI] input port Specifications ■Angle of tilt ■RS-232Ccable layout DECLARATION of CONFORMITY FCC Compliance Statement For United States Users WARNING Glossary Page Index Page Page Page Page General Notice: