Turning On the Phone, Turning Off the Phone | Ericsson R290 instruction

R290 User’s Guide

Use with Portable Hands Free (Globalstar Mode)

Connect the Portable Hands Free unit to the phone. Rotate the antenna to the 90 degrees position. Place the phone on a flat level surface with the antenna vertical as shown below.

The phone may be held in the hand if required but the antenna must always be vertical when used in Globalstar mode. Do not hold the antenna when the phone is IN USE. Holding the antenna affects call quality, may cause the phone to operate at a higher power level than needed and shorten talk and stand-by times.

Use with Mobile Office (Globalstar Mode)

Connect the Mobile Office data cable to the phone. Rotate the antenna to the 90 degrees position. Place the phone on a flat level surface with the antenna vertical as shown above. Do not hold the antenna when the phone is IN USE. Holding the antenna affects call quality, may cause the phone

to operate at a higher power level than needed and shorten talk and stand- by times.

Turning On the Phone

1.Press and hold down the PWR key until the display turns on.

2.Enter your SIM PIN (4 to 8 digits).

3. Press YES.

If you entered your PIN correctly, you will receive a welcome message.

The display will illuminate and the POWER ON TONE will be played. A greeting message will appear on the screen. This message can be personalised see “Greetings” on page 33.

NOTE:

The first time you turn on your phone you will need to enter the PIN (SIM lock code) given to you by your service provider. You may change your PIN or turn the SIM lock off. See “Card Lock (SIM PIN)” on page 41 for instructions. The digits appear as stars (*) in the display. If you make a mistake while entering your PIN, erase the digit by pressing the CLR key.

In order to guard against unauthorised use of both the phone and the SIM, we strongly recommend that you enable both the phone PIN and the SIM PIN. If these are enabled, they will be verified before the phone starts to search for a network.

Turning Off the Phone

To turn off your phone press and hold the PWR key until the display is turned off.

8

Image 16

Ericsson R290 Turning On the Phone, Use with Portable Hands Free Globalstar Mode, Use with Mobile Office Globalstar Mode

Contents

Ericsson R290 Satellite Innovatron Patents Product Care and Maintenance Safety InstructionsGuidelines for Safe and Efficient Use Driving Electronic DevicesAircraft Blasting Areas Battery Information Recycling Your Battery Please note Contents Warranty Introduction About Your Phone Globalstar/GSMOperators & Subscriptions SIM Card Phone Operating Without a SIM Card Preparing Your Phone for UseInserting the SIM Card Battery Charging the Battery R290 User’s Guide Disconnecting the Charger When to Charge the BatteryLow Battery Alarm Antenna Use with Portable Hands Free Globalstar Mode Use with Mobile Office Globalstar ModeTurning On the Phone Turning Off the Phone Navigating the Menu System Display Text and SymbolsTerms Used Indicators in the Display Icon Function Initial Phone Settings Searching for a Network Selecting a Network Stand-by display Making and Receiving Calls Receiving a Call Answering a CallRejecting a Call Calling Line Identification CLI Handling Two Calls Useful Information while Talking To Change the Ring Volume To Change Key Tone VolumeUsing Auto-Redial To Redial the Last Dialled Number Missed Calls Making/Answering a Call with Call Bar ActiveNotification that a Call has been Diverted To dial the last 10 numbers dialled, received or missed Using the Phone Book About the Phone BookInternational Numbers Speed Dialling Upper Case Mode To Store a Name and a Number into a Selected Memory Store Lower Case Mode To Store Your Own Telephone Number To Edit a Number from Memory Store Last Number Stores To Display your Own Telephone NumberDialled Store Last Number Redial Pause DiallingReceived Store Missed Store Sending Dtmf Tones During a Call One-Touch DiallingCall Duration and Cost Last Call Call Cost Setup To Reset the Call Time/Cost CountersAll Calls To Setup the Unit Time for Calls To set the maximum cost ‘ Cost Limit Approaching’ being displayed Personalizing Your Phone Busy Numbers Ring Tone Ring VolumeTo Complete a Ccbs Call Caller ID Escalating Ring VolumeConnect ID Automatic Display of Call Time Auto AnswerGreetings Clock Clock Mode Date ModeSet Time Set Date Satellite Synchronisation Mode Language ModeLanguage To Choose a Language Visual Indicator Usage Power SaveBacklight Operation Fixed Dialled Number Store Handsfree Automatic Shutdown TimerVoice Mail Protecting Your Phone Setting the Keypad LockAbout Locks Phone Lock PIN To Enable the Phone PINTo unlock the keypad Unblocking with Personal Unblocking Key PUK To Disable the Phone PINTo Change the Phone PIN Card Lock SIM PIN To Enable the SIM PIN LockTo change the SIM PIN To Disable the SIM PIN Lock Controlling Your CallsCall Divert To Review the Call Divert Status To Setup Call Divert Notification that a Call has been Diverted Call WaitingTo Remove Call Diversion To Check the Call Wait Status To Cancel Call WaitingTo Set Call Waiting Switching between Active Call and Call on Hold Dealing with Multiple CallsCall Waiting In-Call Menu Placing a Second Call and holding the Current Call Placing a Call when the Called Party is Engaged Conference CallsCall Termination by Calling Party with another Call Held To Create a Conference Call To Review the Participants in a Conference Call Call Control Public MMI Commands Summary To Disconnect a Remote Party from a Conference CallCall Hold and Call Termination by a Remote Party Remote Party Notification Call Barring To Check the Call Bar Status To Set Outgoing Call Barring To Set Incoming Call Barring To Cancel Outgoing Call Barring To Cancel Incoming Call Barring To Change the Network Password for Call Barring Quick access to unread messages Sending And Receiving Text MessagesReceiving a Message Checking Subscription Deleting a Message To Read a MessageSaving and Dialling a Number Received in a Message To Select Message Tones Clearing Messages Automatically Sending a Message Displaying Priority Messages ImmediatelyTo Originate a New Message To Enter Message Text To Enter the Service Centre NumberTo Enter the Destination Address To Enter the Validity Period To Select the Message TypeTo Review Your Newly Created Message To Create a Message from an Existing Message To Send the Completed Message To Save a MessageTo Return to the Current Message and complete it To Delete a Message To Set the Message Parameter Defaults To Check on the Status of the Last Message Sent Warranty Our WarrantyWhat We Will Do Conditions Patents R290 User’s Guide Index PIN