Table of Contents | EVGA 122-M2-NF59-AX guide

TABLE OF CONTENTS (Continued)

Nvidia Networking Guide (continued)
Configuring TCP/IP Acceleration	45
Configuring Teaming	46
MediaShield RAID Manager	46
Create RAID Arrays	47
Nvidia nTune 5.0	53
Starting nTune	53
Adjust Motherboard Settings	54
Adjust GPU Settings	55
Dynamic BIOS Access	56
Tune System	56
View System Information	57
Nvidia Monitor	29
Driver Installation	59
RAID Installation
APPENDIX 1 - POST CODES	61
Quick Debug POST Codes	61
Boot Block POST Codes	62
APPENDIX 2 - TRADEMARKS AND NOTICES	64
Copyrights, Trademarks, and Notices	64
FCC Compliance Statement	64
APPENDIX 3 - CONTACTING SUPPORT AND OTHER USEFUL INFORMATION	65

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 3

Image 4

EVGA 122-M2-NF59-AX manual Table of Contents

Contents

Page Evga Nforce 590 SLI Motherboard CPU Support Table of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan Specifications CPU Socket AM2 Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Hardware Installation Hardware Installation Steps Cmos RAM Clear Setting Install CPU Glossary About AMD Athlon64 AM2 CPUs Install Memory Valid Memory Configurations For Dual Channel Memory Expansion Cards Procedure For Expansion Card Installation Assigning IRQs For Expansion Card PCI-Express Slots Interrupt Request Table For This MotherboardFrom TOP to Bottom Standard Interrupt Assignments IRQ SLI Bridge for Nvidia SLI Supported VGA Cards Page Connectors and Headers Power Connector 24-pin block Atxpwr PIN ROW1 ROW2 PS/2 Mouse & PS/2 Keyboard Connector KB ATX 12V Power Connector 8-pin block ATX12VLAN Port connector UL1 MIC Pink CEN/LEF Blackness Primary IDE Connector 40-pin block IDE1 Floppy drive Connector 34-pin block FDDPin Serial-ATA Port Connectors Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Audio Headers Line-Out/MIC Header for Front Panel 9-pin AudioUSB Port Headers 9-pin USB1/USB2/USB3 Speak PwrledJW FP FAN Headers 3-pin CPUFAN, SYSFAN1 CD Audio-In Headers 4-pin Cdin Firewire Connectors 1394A~B Supplemental SLI Power J2 Starting Up Your Computer Beep Meaning Bios Description Enter Bios Setup Standard Cmos FeaturesAdvanced Bios Features Advanced Chipset Features Load Defaults Set PasswordSave & Exit Setup Set User Name Halt On Floppy Drive aMemory Advanced Bios Features Removable Device Priority Hard Disk Boot PriorityNetwork Boot Priority Quick Power On Self Test LPC P2P P2P Frequency Settings Ref Clock HTT CPU MultiplierPCIe Bus, Slot SPP MCP Ref Clock CPU Memory Configuration Optimized for nForce Mem Drive Strength settingCKE base power down mode CKE power down control Memory Timings Standard Memory Settings Timing mode Command Per Clock CMDAdvance Memory Settings tRRD Read delay from Rx Fifo Dram driver weak mode CKE drive strengthCS drive strength MA drive strength IDE Function Setup RAID ConfigUSB Config MAC Config Power-on by Alarm Power on FunctionAcpi Suspend Type States Support Reset Configuration Data Init Display FirstResources Controlled by IRQ Resources Temperature Values Password Disabled Press any key to continue…System Board Quit Without Saving Y/N? Save to Cmos and Exit Y/N?Nvidia Networking Guide Launching Nvidia Networking Configuring FirstPacket Enabling FirstPacket Configuring TCP/IP Acceleration Configuring Teaming MediaShield RAID Manager Create RAID Arrays Configuration Options Setting Up a Custom Array Creating a Mirrored Array RAID configuration information appears, as shown in Figure View RAID Arrays Delete RAID Arrays Delete Array Wizard Setting Up a Spare RAID Disk Free DiskDedicated Disk Assigning a Free Disk Nvidia nTunre Starting nTune Adjust Motherboard Settings Performance Category Adjust GPU Settings Dynamic Bios Access Tune System Adjust Custom Rules View System Information Perform Stability Test Nvidia Monitor Driver Installation RAID InstallationPage Appendix Quick Debug Port Post CodesPage Page Page COPYRIGHTS, TRADEMARKS, Notices FCC Compliance Information Useful Information Contacting Customer ServiceInformation to Keep Handy Before Calling