Appendix, Quick Debug Port Post Codes | EVGA 122-M2-NF59-AX instruction

APPENDIX 1

Quick Debug Port Post Codes

Please refer to the following Quick Debug table to assist in troubleshooting problems that are revealed through the motherboard’s Debug Port. If you need more detailed information, you can refer to the Detailed Debug tables in the following pages.

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 60

Image 61

EVGA 122-M2-NF59-AX manual Appendix, Quick Debug Port Post Codes

Contents

Page CPU Support Evga Nforce 590 SLI Motherboard Table of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan CPU Socket AM2 Specifications Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Cmos RAM Clear Setting Hardware Installation Hardware Installation Steps About AMD Athlon64 AM2 CPUs Install CPU Glossary Valid Memory Configurations Install Memory For Dual Channel Memory Assigning IRQs For Expansion Card Expansion Cards Procedure For Expansion Card Installation PCI-Express Slots Interrupt Request Table For This MotherboardFrom TOP to Bottom IRQ Standard Interrupt Assignments SLI Bridge for Nvidia SLI Supported VGA Cards Page PIN ROW1 ROW2 Connectors and Headers Power Connector 24-pin block Atxpwr PS/2 Mouse & PS/2 Keyboard Connector KB ATX 12V Power Connector 8-pin block ATX12VLAN Port connector UL1 CEN/LEF Blackness MIC Pink Primary IDE Connector 40-pin block IDE1 Floppy drive Connector 34-pin block FDDPin Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Serial-ATA Port Connectors Audio Headers Line-Out/MIC Header for Front Panel 9-pin AudioUSB Port Headers 9-pin USB1/USB2/USB3 Speak PwrledJW FP CD Audio-In Headers 4-pin Cdin FAN Headers 3-pin CPUFAN, SYSFAN1 Supplemental SLI Power J2 Firewire Connectors 1394A~B Beep Meaning Starting Up Your Computer Standard Cmos Features Bios Description Enter Bios SetupAdvanced Bios Features Advanced Chipset Features Set Password Load DefaultsSave & Exit Setup Set User Name Halt On Floppy Drive aMemory Hard Disk Boot Priority Advanced Bios Features Removable Device PriorityNetwork Boot Priority Quick Power On Self Test LPC P2P P2P CPU Multiplier Frequency Settings Ref Clock HTTPCIe Bus, Slot SPP MCP Ref Clock CPU Drive Strength setting Memory Configuration Optimized for nForce MemCKE base power down mode CKE power down control Command Per Clock CMD Memory Timings Standard Memory Settings Timing modeAdvance Memory Settings tRRD Read delay from Rx Fifo CKE drive strength Dram driver weak modeCS drive strength MA drive strength RAID Config IDE Function SetupUSB Config MAC Config Power on Function Power-on by AlarmAcpi Suspend Type States Support Init Display First Reset Configuration DataResources Controlled by IRQ Resources Password Disabled Press any key to continue… Temperature ValuesSystem Board Quit Without Saving Y/N? Save to Cmos and Exit Y/N?Nvidia Networking Guide Launching Nvidia Networking Enabling FirstPacket Configuring FirstPacket Configuring TCP/IP Acceleration MediaShield RAID Manager Configuring Teaming Create RAID Arrays Setting Up a Custom Array Configuration Options Creating a Mirrored Array View RAID Arrays RAID configuration information appears, as shown in Figure Delete Array Wizard Delete RAID Arrays Free Disk Setting Up a Spare RAID DiskDedicated Disk Assigning a Free Disk Starting nTune Nvidia nTunre Performance Category Adjust Motherboard Settings Adjust GPU Settings Tune System Dynamic Bios Access View System Information Adjust Custom Rules Nvidia Monitor Perform Stability Test RAID Installation Driver InstallationPage Quick Debug Port Post Codes AppendixPage Page Page FCC Compliance Information COPYRIGHTS, TRADEMARKS, Notices Useful Information Contacting Customer ServiceInformation to Keep Handy Before Calling