EVGA 122-M2-NF59-AX specs

STEP 3 - Be careful with the pins as to not damage the adapter or graphics cards during installation.

STEP 4 - Plug the SLI Bridge adapter onto both of the NVIDIA SLI Supported VGA Cards

EVGA Corporation 2900 Saturn St. Suite B, Brea, CA 92821

Phone: 888 / 881-EVGA - 714 / 528-4500 - Fax: 714 / 528-4501

Page 17

Image 18

EVGA 122-M2-NF59-AX manual

Contents

Page Evga Nforce 590 SLI Motherboard CPU Support Table of Contents Table of Contents Introduction of nForce 590 Motherboards Motherboard Features CPU Smart Fan Specifications CPU Socket AM2 Layout Diagram & Jumper Settings JUMPERS, CONNECTORS, HEADERS, and Sockets Hardware Installation Hardware Installation Steps Cmos RAM Clear Setting Install CPU Glossary About AMD Athlon64 AM2 CPUs Install Memory Valid Memory Configurations For Dual Channel Memory Expansion Cards Procedure For Expansion Card Installation Assigning IRQs For Expansion Card Interrupt Request Table For This Motherboard PCI-Express SlotsFrom TOP to Bottom Standard Interrupt Assignments IRQ SLI Bridge for Nvidia SLI Supported VGA Cards Page Connectors and Headers Power Connector 24-pin block Atxpwr PIN ROW1 ROW2 ATX 12V Power Connector 8-pin block ATX12V PS/2 Mouse & PS/2 Keyboard Connector KBLAN Port connector UL1 MIC Pink CEN/LEF Blackness Floppy drive Connector 34-pin block FDD Primary IDE Connector 40-pin block IDE1Pin Serial-ATA Port Connectors Serial-ATA Port SATA1 / SATA2 / SATA3/ SATA4/ SATA5 /SATA Headers Line-Out/MIC Header for Front Panel 9-pin Audio AudioUSB Port Headers 9-pin USB1/USB2/USB3 Pwrled SpeakJW FP FAN Headers 3-pin CPUFAN, SYSFAN1 CD Audio-In Headers 4-pin Cdin Firewire Connectors 1394A~B Supplemental SLI Power J2 Starting Up Your Computer Beep Meaning Advanced Bios Features Bios Description Enter Bios SetupStandard Cmos Features Advanced Chipset Features Save & Exit Setup Load DefaultsSet Password Set User Name Floppy Drive a Halt OnMemory Network Boot Priority Advanced Bios Features Removable Device PriorityHard Disk Boot Priority Quick Power On Self Test LPC P2P P2P PCIe Bus, Slot Frequency Settings Ref Clock HTTCPU Multiplier SPP MCP Ref Clock CPU CKE base power down mode Memory Configuration Optimized for nForce MemDrive Strength setting CKE power down control Advance Memory Settings tRRD Memory Timings Standard Memory Settings Timing modeCommand Per Clock CMD Read delay from Rx Fifo CS drive strength Dram driver weak modeCKE drive strength MA drive strength USB Config IDE Function SetupRAID Config MAC Config Acpi Suspend Type Power-on by AlarmPower on Function States Support Resources Controlled by Reset Configuration DataInit Display First IRQ Resources System Temperature ValuesPassword Disabled Press any key to continue… Board Save to Cmos and Exit Y/N? Quit Without Saving Y/N?Nvidia Networking Guide Launching Nvidia Networking Configuring FirstPacket Enabling FirstPacket Configuring TCP/IP Acceleration Configuring Teaming MediaShield RAID Manager Create RAID Arrays Configuration Options Setting Up a Custom Array Creating a Mirrored Array RAID configuration information appears, as shown in Figure View RAID Arrays Delete RAID Arrays Delete Array Wizard Dedicated Disk Setting Up a Spare RAID DiskFree Disk Assigning a Free Disk Nvidia nTunre Starting nTune Adjust Motherboard Settings Performance Category Adjust GPU Settings Dynamic Bios Access Tune System Adjust Custom Rules View System Information Perform Stability Test Nvidia Monitor Driver Installation RAID InstallationPage Appendix Quick Debug Port Post CodesPage Page Page COPYRIGHTS, TRADEMARKS, Notices FCC Compliance Information Contacting Customer Service Useful InformationInformation to Keep Handy Before Calling