Manuals / Extreme Networks / Computer Equipment / Switch

Extreme Networks 8800 Series manual Disconnecting a BlackDiamond 8810 AC Power Cord

Models: 8800 Series

1 180

Download 180 pages 30.86 Kb

Page 127

BlackDiamond 8810 AC Power Cord Retaining Bracket

6Tighten the captive screws in the middle and on each end of the power cord retaining bracket (see Figure 81).

Figure 81: Securing the BlackDiamond 8810 AC Power Cord Retaining Bracket

REMOVE TO INSTALL POWER CORDS

ASP012B

7To power the system on, connect the other end of each installed AC power cord to the power source.

NOTE

Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components.

Disconnecting a BlackDiamond 8810 AC Power Cord

To disconnect a BlackDiamond 8810 AC power cord:

1Attach the ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle on the top left corner of the switch chassis.

2Disconnect the AC power cord from the power source.

3Loosen the captive screws in the middle and on each end of the BlackDiamond AC power cord retaining bracket, using a #2 Phillips screwdriver.

4Remove the BlackDiamond AC power cord retaining bracket from the front of the switch.

5Remove the end of the AC power cord from the power outlet(s) on the front of the switch.

NOTE

Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components.

BlackDiamond 8800 Series Switches Hardware Installation Guide	127

Image 127

Extreme Networks 8800 Series manual Disconnecting a BlackDiamond 8810 AC Power Cord

Contents

Page Page Table of Contents Table of Contents 101 Replacing the Power Cable125 Part 3 Installing BlackDiamond Switch AccessoriesPart 4 BlackDiamond Maintenance Procedures 119167 Table of Contents Introduction PrefaceConventions Text Conventions Related PublicationsPreface Related Publications Preface About the BlackDiamond 8800 Series Switches Page Overview of the BlackDiamond 8800 Series Switches Management Ports BlackDiamond 8806 Switch ChassisAbout the BlackDiamond 8800 Series Switches Full-Duplex SupportFront of the BlackDiamond 8806 Chassis BlackDiamond 8806 Switch ChassisFront of the BlackDiamond 8810 Chassis BlackDiamond 8810 Switch ChassisRear Panel of the BlackDiamond 8810 Chassis BlackDiamond 8810 Switch ChassisAbout the BlackDiamond 8800 Series Switches Redundant MSM Activity Management Switch Modules MSMBlackDiamond 8800 Series Modules Overview of the BlackDiamond 8800 Series ModulesBlackDiamond 8800 Series Modules MSM Physical FeaturesMSM-48c Management Switch Modules MSMMSM LEDs ModulesMSM-G8X, MSM-48. and MSM-48c LEDs G24X I/O Module BlackDiamond 8800 Original Series I/O ModulesModules G24X I/O Module 10G4X I/O ModuleG48T I/O Module G48T I/O ModuleG48P I/O Module BlackDiamond 8800 a-Series I/O ModulesG48Ta I/O Module G48Ta I/O ModuleG48Xa I/O Module G48Xa I/O Module10G4Ca I/O Module 10G4Xa I/O ModuleG48Tc I/O Module BlackDiamond 8800 c-Series I/O Modules10G4Xc I/O Module 10G4Xc I/O ModuleG24Xc I/O Module 10G8Xc I/O ModuleG48Xc I/O Module G48Xc I/O ModuleG48Te I/O Module BlackDiamond 8800 E-Series I/O ModulesG48Pe I/O Module G48Pe I/O ModuleG48Te2 I/O Module Module LEDsPort LEDs on Non-PoE Modules Module LEDsBlackDiamond 8800 Series I/O Module LEDs Port LEDs for the PoE-capable I/O Modules PSU Compatibility in BlackDiamond 8800 Series Switches Power Supply Units for BlackDiamond 8800 Series SwitchesExtreme Networks 700/1200 W AC PSU Power Supply Units for BlackDiamond 8800 Series SwitchesLEDs Extreme Networks 700/1200 W AC PSU Power Supply CordsFuse LEDs on the 700/1200 W AC PSUSpecifications Minimum Software Required Extreme Networks 600/900 W AC PSUExtreme Networks 600/900 W AC PSU LEDs on the Extreme Networks 600/900 W AC PSU Combining Different AC PSU Models Combining Different AC PSU Models1200 W DC PSU Extreme Networks 1200 W DC PSUExtreme Networks 1200 W DC PSU LEDs on the Extreme Networks 1200 W DC PSUPower Supply Units for BlackDiamond 8800 Series Switches Installing BlackDiamond 8800 Series Switches Modules Planning Your Site Site PreparationSite Preparation Meeting Site RequirementsOperating Environment Requirements Building and Electrical CodesTemperature Wiring Closet ConsiderationsMeeting Site Requirements Chassis Spacing Requirements HumidityChassis Airflow Requirements Airflow Through the BlackDiamond 8810 Chassis Electrostatic DischargeMechanical Recommendations for the Rack Rack Specifications and RecommendationsProtective Grounding for the Rack Securing the Rack Space Requirements for the RackCabling Standards Evaluating and Meeting Cable RequirementsCable Labeling and Record Keeping Evaluating and Meeting Cable Requirements Installing CableProperly Installed and Bundled Cable Cable Distances Fiber Optic CableMedia Types and Maximum Distances RJ-45 Connector Jacket Types RJ-45 Connector JacketsRadio Frequency Interference Power Supply Requirements Meeting Power RequirementsPoE Devices AC Power Cable Requirements AC Power Cable RequirementsUninterruptible Power Supply Requirements Replacing the Power CableUPS Transition Time Applicable Industry StandardsSelecting a UPS Calculating Volt-Amperage RequirementsApplicable Industry Standards Site Preparation Installing the BlackDiamond 8800 Series Chassis Unpacking the BlackDiamond 8806 Chassis Installing the BlackDiamond 8800 Series ChassisUnpacking the BlackDiamond 8806 Chassis Clip Locks on the BlackDiamond 8806 Chassis Shipping CartonCorrect Method for Lifting the BlackDiamond 8806 Chassis Unpacking the BlackDiamond 8810 Chassis Unpacking the BlackDiamond 8810 ChassisClip Locks on the BlackDiamond 8810 Shipping Carton Unpacking the BlackDiamond 8810 Chassis Attaching the Mid-Mount Brackets Pre-installation RequirementsAttaching the Mid-Mount Brackets Rack-Mounting the BlackDiamond 8800 Series Chassis Rack-Mounting the BlackDiamond 8800 Series Chassis Mounting the 19-inch Helper Bracket onto the System RackSecuring the BlackDiamond 8806 Chassis to a Rack Grounding the BlackDiamond 8800 Series Chassis Grounding the BlackDiamond 8800 Series ChassisBack of BlackDiamond 8806 Chassis Initial Management Access Initial Management AccessInstalling the BlackDiamond 8800 Series Chassis Safety Combining Different AC PSU Models PSU CompatibilityMinimum Software Requirements Power Supply Cords for AC Power SuppliesAC Power Supply Cords Power Supply Cords for AC Power SuppliesInstalling an Extreme Networks AC PSU Installing an Extreme Networks AC PSU Installing the PSURequired Tools and Equipment Removing or Replacing an Extreme Networks AC PSU Inserting an AC PSU into the Power Supply BayLEDs on the 700/1200 W AC PSU Power Predictive Fail PSU Condition Green AmberInstalling the DC Wiring Installing an Extreme Networks 1200 W DC PSUInstalling an Extreme Networks 1200 W DC PSU Installing a 1200 W DC PSULocking Handle on the 1200 W DC PSU Connecting the Input Cable to the 1200 W DC PSU Removing a 1200 W DC PSU DC Cable Connector on the 1200 W DC PSUExtreme Networks 1200 W DC PSU LEDs 100 Module Slot Assignments Distinguishing an MSM from an I/O Module Installing a BlackDiamond 8800 Series ModuleStore the module packaging for future use Installing a BlackDiamond 8800 Series ModuleInjector/ejector Handles in an Open Position Locking the Module into Place Making Network Interface Cable Connections Connecting and Disconnecting Cables on the 10G4Ca ModuleMaking Network Interface Cable Connections Connecting a 10G4Ca Module PortModule LED Activity for Normal Operation Installing a Backup MSMVerifying the Module Installation Displaying Slot Status InformationRemoving a BlackDiamond 8800 Series Module Removing a BlackDiamond 8800 Series ModuleIndications that the Module is Unlocked Blank Front PanelsRemoving a Blank Front Panel Installing a Blank Front PanelBlank Front Panels 112 Installing or Removing an External Compact Flash Memory Card Logging In for the First Time Connecting Equipment to the Console Port115 116 Installing BlackDiamond Switch Accessories Page Installing an S-POE Daughter Card Installing BlackDiamond 8800 Series Module OptionsSeating the S-POE Card on the I/O Module Installing BlackDiamond 8800 Series Module OptionsRemoving an S-POE Card Removing an S-POE CardOption Slot Cover Plate Installing an Option Card in the MSM-48cInserting the Option Card Installing an Option Card in the MSM-48cRemoving an Option Card Removing an MSM Option CardBlackDiamond 8810 AC Power Cord Retaining Bracket BlackDiamond AC Power Cord Retaining BracketsBlackDiamond AC Power Cord Retaining Brackets Connecting an AC Power Cord to the BlackDiamond 8810 SwitchBlackDiamond 8810 AC Power Cord Retaining Bracket Disconnecting a BlackDiamond 8810 AC Power CordInstalling and Routing the AC Power Cords BlackDiamond 8806 AC Power Cord Retainer ChannelBlackDiamond 8806 AC Power Cord Retainer Channel BlackDiamond 8806 AC Power Cord Retainer ChannelRouting the Power Cords in the Channel BlackDiamond Cable Management Using the Cable Holders and Cable ClipsAbout BlackDiamond Cable Management BlackDiamond Cable Management Connecting Cable HoldersUsing the Cable Holders and Cable Clips Connecting Cable ClipsCable clip chain BlackDiamond Maintenance Procedures 136 Removing the Fan Tray Pre-Installation RequirementsReplacing BlackDiamond 8800 Series Chassis Components Replacing the Fan TrayReplacing BlackDiamond 8800 Series Chassis Components Removing the Fan Tray from the BlackDiamond 8810 SwitchReplacing the Fan Tray Installing the Fan Tray in the BlackDiamond 8810 SwitchReplacing the PSU/Fan Controller Installing the Fan Tray in the BlackDiamond 8806 SwitchReplacing the PSU/Fan Controller Removing the PSU/Fan ControllerRemoving the Access Cover from the BlackDiamond 8806 Switch Installing the Replacement PSU/Fan Controller 144 Repacking a BlackDiamond 8800 Series Chassis Safety InformationRequired Tools and Equipment Repacking a BlackDiamond 8800 Series Chassis Repacking the BlackDiamond 8810 ChassisRepacking the BlackDiamond 8810 Chassis Recrating the BlackDiamond 8810 Chassis Packing Foam in the BlackDiamond 8810 Shipping Carton Repacking the BlackDiamond 8806 Chassis Setting the BlackDiamond 8806 Chassis onto the Foam CushionRepacking the BlackDiamond 8806 Chassis Placing the Carton over the BlackDiamond 8806 Chassis152 Appendixes Page Considerations Before Installing Safety InformationInstalling Power Supply Units Safety Information Maintenance SafetyGeneral Safety Precautions General Safety PrecautionsCable Routing for LAN Systems Black Diamond SSI AC PSU Model Selecting Power Supply CordsFiber Optic Ports-Optical Safety Battery Replacement and DisposalBattery Replacement and Disposal GBIC, SFP Mini-GBIC, XENPAK, and XFP Regulatory Compliance Fiber Optic Ports-Optical Safety Hinweise zur InstallationSicherheitshinweise Installation von Netzteilen Allgemeine Sicherheitsvorkehrungen WartungssicherheitAuswahl der Stromkabel 164 Lichtleiteranschlüsse Optische Sicherheit Austauschen und Entsorgen von Batterien166 BlackDiamond 8810 Switch Technical SpecificationsBlackDiamond 8810 Switch Technical Specifications EMI/EMC Standards Technical SpecificationsBlackDiamond 8810 Switch BlackDiamond 8806 switch Technical Specifications BlackDiamond 8806 SwitchBlackDiamond 8806 Switch Specifications for the AC PS Model #41050 600/900 W AC PSU Power Supplies for BlackDiamond 8800 Series SwitchesConnector Pinouts Connector PinoutsSpecifications for the DC SSI PS Model #60021 1200 W DC PSU Pinouts for the DB-9 Console ConnectorNull-modem Cable Pinouts Switch PC/Terminal Numerics IndexESD IndexIndex MSM Index Index