Extron electronic DVS 406 AD, DVS 406 D manual Rear panel video inputs, Rear panel audio inputs

Quick Start — DVS 406

Installation

Step 1

Turn off power to the scaler and input and output devices, and remove power cords from them.

Step 2

Install the four rubber feet on the bottom of the DVS 406 scaler, or mount the scaler in a rack.

Step 3

Attach input devices to the scaler.

Rear panel video inputs

Input 1: RGB and HD YUV pass-through

	HD YUV to / RGB PASS THROUGH					HD YUV to / RGB PASS THROUGH
R	G	B	H	V	R	G	B	H	V
/R-Y	/Y	/B-Y	/HV		/R-Y	/Y	/B-Y	/HV
	RGBHV						RGBS
		input					input
	HD YUV to / RGB PASS THROUGH					HD YUV to / RGB PASS THROUGH
R	G	B	H	V	R	G	B	H	V
/R-Y	/Y	/B-Y	/HV		/R-Y	/Y	/B-Y	/HV
		RGsB			HDTV Component (YUV)
		input				video input
Input 2: RGB pass-through, RGBcS,YUVi, YUVp
R	G	B	H	V	R	G	B	H	V
/R-Y	/Y	/B-Y	/HV		/R-Y	/Y	/B-Y	/HV
2 - RGB PASS THROUGH / R-Y, B-Y, Y						2 - RGB PASS THROUGH		/ R-Y, B-Y, Y
	RGBHV						RGBS
	input						input
R	G	B	H	V	R	G	B	H	V
/R-Y	/Y	/B-Y	/HV		/R-Y	/Y	/B-Y	/HV
	2 - RGB PASS THROUGH		/ R-Y, B-Y, Y			2 - RGB PASS THROUGH / R-Y, B-Y, Y
		RGsB				RGBcS
		input					input
R	G	B	H	V
/R-Y	/Y	/B-Y	/HV
	2 - RGB PASS THROUGH / R-Y, B-Y, Y
	Component
	video input
	(R-Y, Y, B-Y)
Inputs 3 - 5: composite video, S-video
	Y			Y
	/VID			/VID
	C			C
Composite video				S-video
input				input
Input 6: SDI (serial digital interface)
Attach an SDI source to this BNC								SDI
(DVS 406 D and DVS 406 AD models only).

Rear panel audio inputs
						600 ohms
Tip	AUDIO	Tip	L R	AUDIO	Tip	L R	AUDIO
L R		Ring			Ring
Sleeve
		Sleeve (s)			Sleeve (s)
Tip		Tip			Tip
Sleeve		Ring			Ring

600 ohms

Unbalanced Input	Balanced Input	Balanced Input
(high impedance)	(high impedance)	(600 ohms)

Inputs 1 - 6: balanced and unbalanced

Step 4

Attach output devices to the scaler.

Rear panel video output

Output BNC connectors

R	G	B	H/HV	V	R	G	B	H/HV	V
		RGBHV					RGBS
R	G	B	H/HV	V

RGsB (Sync on Green)

RsGsBs (output only if input is RsGsBs)

RGB

Output 15-pin HD connector

Both connectors will output simultaneously. The sync format is the same for both outputs.

Rear panel audio output

Unbalanced Output Balanced Output

Tip	LR	AUDIO	Tip	LR	AUDIO
See Caution			Ring
Sleeve (s)			Sleeve (s)
Tip			Tip
See Caution			Ring

CAUTION Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

Step 5

Plug the DVS 406, and input and output devices into a grounded AC source, and turn on the input and output devices.

Step 6

Use the LCD menu screens (see the next page) or RS-232 programming to configure the scaler. See chapter two for installation and operation procedures, and see chapter three for programming information.

Application Example

INPUT
BUFFERED LOCAL	H. SHIFT
MONITOR OUTPUT

RGB 109xi

VGA INTERFACE W/ADSP

RGB 109xi

VCR
DVD Player	Video Camera 2
PC Computer
Codec
	RS-232
DVS 406	Control

1 - RGB PASS THROUGH

3

4

5

6

INPUTS

OUTPUT

I

L 1 R

L 2 R

L 3 R

L 4 R

L 5 R

L 6 R

L

R

N

H

Y

Y

Y

T

R

G

B

V

P

/HV

/VID

/VID

/VID

RGB

R

G

B

H/HV

RS-232

SDI

V

U

O

T

R

G

B

H

V

C

C

C

U

S

/RY

/Y

/B-Y

/HV

T

2 - RGB PASS THROUGH / R-Y, B-Y, Y

Video Camera 1		Projector
	Plasma Display

DVS 406 • Quick Start QS-1