Extron electronic MPX 866 A Command/Response Table for SIS Commands continued, ASCII Command

Command/Response Table for SIS Commands (continued)

Command	ASCII Command	Response	Additional description
	(Host to Unit)	(Unit to Host)

Lock (executive) modes

NOTE: See “Setting the Front Panel Locks (Executive Modes)” in the Operation section for more information on the Lock modes.

Lock all front panel functions	1X
Lock advanced front panel	2X
functions
Unlock all front panel	0X
functions
View lock status	X

Exe1]	Enable Lock mode 1.
Exe2]	Enable Lock mode 2.
Exe0]	Enable Lock mode 0.
X1*]

Resets

Reset global presets and	EZG}	Zpg]
names
Reset one global preset	EX1)ZG}	ZpgX1)]
Reset audio input levels	EZA}	Zpa]
Reset audio output levels	EZV}	Zpv]
Reset all mutes	EZZ}	Zpz]
Reset whole switcher	EZXXX}	Zpx]
Absolute reset	EZQQQ}	Zpq]

Clear all global presets and their names.

Clear global preset X1). Reset all audio input levels (gain and attenuation) to 0 dB.

Reset all audio output levels (volume) to 100% (no attenuation).

Unmute all outputs.

Clear all ties and presets, reset all all audio gains to 0 dB, and reset volume to 100%. Similar to Reset whole switcher, plus clear all UART ports, reset the IP address to 192.168.254.254 and reset the subnet mask to 255.255.000.000.

Information requests

Information request	I	V14X12•A14X06]	This matrix switcher has 14 video and audio
			inputs by 12 video and 6 audio outputs.
Request part number	N	60-825-01]

NOTE: There are up to three separate sets of Extron firmware on which the switcher can report: the controller firmware, which is the overall control firmware; the Ethernet protocol firmware, which handles the Ethernet interface; and the latest optional Extron firmware update, which is available at www.extron.com.

Query firmware version			Q	X1$]
Query controller firmware			0Q	X1$-X1%-X1%]	Provide a detailed status of the Ethernet protocol
version (verbose)					firmware, the controller firmware, and any
					firmware upgrade. An asterisk (*) marks the
					firmware that is running is by . A caret (^)
					marks that the firmware has a bad checksum
					or an invalid load. ?.?? marks that firmware is
					not loaded.
Response description:			Ethernet protocol firmware version-controller firmware version-updated firmware version]
Example:			0q
		Description		* indicates the version running	Upload date and time
	1.23-0.14(0.20-MPX866Series			-Thu, 20 Jul 2006 00:00:00 GMT)-0.25*(0.24-64x64 Series -Fri, 28 Jul 2006 16:39:21 GMT)
	Ethernet			MPX firmware version	Updated firmware version
	protocol
	firmware
Request system status			S	X1^•X1^•X1^•X1^•X1^•X1^•X1&]
Response description:			S	+3.3V•+5V•–5V•+2.5V•–15V•+15V•Temp]
Example:			S		+15V power system at +15.15V

3.29•5.04•-5.14•2.48•-15.27•15.15•120.20

			3.3V power system at 3.29V	Temperature 120.20 degrees
NOTE: X1) = Global preset #		32 maximum
X1$ = Firmware version number to second decimal place (x.xx)
X1%	= Verbose firmware version-description-upload date/time. See above.
X1^ = Voltage		Positive or negative voltage and magnitude
X1& = Temperature		Degrees Fahrenheit
X1*	= Front panel locks (Executive modes)		0 = Mode 0	1 = Mode 1 2 = Mode 2

MPX 866 A Media Presentation Matrix Switcher • Programming Guide 71