Installation, cont’d, Unbalanced audio | Extron electronic MSG0808

Installation, cont’d

Audio input and output

Before connecting audio, determine whether your audio system is unbalanced or balanced. Then, follow the instructions and illustrations below to connect either unbalanced audio or balanced audio.

CAUTION

Wiring the audio incorrectly can damage the audio output circuits.

Pay special attention to the right channel wiring. The + and – layout differs from most other Extron products.

Unbalanced Input/Output

R	Tip
OUT	See Caution
OUT	Sleeve (s)
L	See Caution
	Tip

OUT L R

Balanced Input/Output

Tip

Ring

Sleeve (s)

Ring

Tip

Figure 2-5— Unbalanced and Balanced audio connections

Unbalanced audio

1. Attach the audio cable to an unbalanced input connector.

2. Attach the other end of the audio cable to the 5-pole captive screw audio cable connector (Extron part number 10-163-05), as shown in figure 2-5. Fasten the captive screws inside the audio cable connector as shown in figure 2-6.

Figure 2-6 — Fastening captive screws

CAUTION

Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

3. Slide the 5-pole captive screw audio cable connector into the audio connector of the switcher, and plug the other end of the audio cable into an amplifier or powered speakers.

Balanced audio

1. Attach the audio cable to a balanced input connector.

2. Attach the other end of the audio cable to the 5-pole captive screw audio cable connector (Extron part number 10-163-05), as shown in figure 2-5. Fasten the captive screws inside the audio cable connector as shown in figure 2-6.

CAUTION

Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

3. Slide the 5-pole captive screw audio cable connector into the audio connector of the switcher, and plug the other end of the audio cable into an amplifier or powered speakers.

2-6 MSG Matrix Switchers • Installation

Image 16

Extron electronic MSG0808, MSG0804 manual Installation, cont’d, Audio input and output, Unbalanced audio, Balanced audio

Contents

Matrix Switchers MSG0804 and MSG0808 Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch Quick Start MSG0804 and MSG0808 Connecting the MSG0808Rack mounting the MSG0808 Quick Start MSG0804 and MSG0808, cont’d Operation Table of Contents Table of Contents, cont’d One Introduction About the MSG Matrix Switchers MSG Matrix Switcher FeaturesMSG Matrix Switchers Introduction Introduction Flexible Control Options This page intentionally left blank Installation Two Installation Mounting the SwitcherMSG Matrix Switchers Installation Tabletop use Rear Panel Connectors Video Inputs Video Outputs Installation, cont’d RS-485 Half Duplex Connection Connecting the MSG0804 and MSG0808 MSG0808 installation example Installation, cont’d Audio input and outputUnbalanced audio Balanced audio Vertical Interval Switching Connecting the external sync signal This page intentionally left blank Three Operation MSG Matrix Switchers Operation Front Panel FeaturesOperation Connecting inputs with outputs Preset configurationsFront Panel Operation Miscellaneous front panel functions Reset to factory default Selecting the switching level audio versions onlyOperation, cont’d Four Windows-based Control Program Using the Software Installing the Windows-based ICS100 Control SoftwareWindows-based Control Program, Cont’d Using the control panel ICS100 Interface screen MSG switcher controls options Setting volume levels Adjusting output volume levelsDefining input icons and labels Creating a new patch Adjusting input volume levels ICS100 Set Output Volume window Setting and using presets Opening the Options menu VIS Enable Enable ResponseUsing Terminal Comm Resetting the unit This page intentionally left blank Remote Control Five Dip Switch Settings Remote ControlMSG Matrix Switchers Remote Control Addressing commands Host-to-MSG Matrix Switcher CommunicationsUsing the command table Remote Control, cont’d Command TableSet-up commands Command Description Switching commands Volume commandsSwitching levels audio models only Blank output Mute all outputs Stop volume ramp Remote Control from a Network Preset commandsEnabling remote control of the switcher over a network Change input volume level global Instructions for configuring the client remote PC ICS100 Serial Port Server window Adjusting response time Adjusting the response timeStopping communication Stopping communications from the server PC CTL120-2 IR Remote Control Press this button first Remote Control, cont’d Specifications AAppendix Specifications VideoVideo input Video output MSG Matrix Switchers Specifications A-3 SyncAudio audio models only Audio input Specifications MSG0804 and MSG0808 Control/remote switcherMSG Matrix Switchers Specifications General BAppendix Reference Information Reference Information To update the firmwareUpdating the Firmware Installing the custom nameplates Installing Custom Engraved NameplatesMSG Matrix Switchers Reference Information MSG Matrix Switcher part numbers Optional accessoriesReference Information, cont’d Part Numbers Plenum Seventeen Conductor Installation Cable Assorted connectors BNC connectorsPre-cut cables Extron Part BNC-4 Mini HR Cable This page intentionally left blank FCC Class a Notice Extron’s Warranty Extron Electronics, USA