Quick Start MSG0804 and MSG0808 | Extron electronic specs

RS-232

1 2 3

RS-422/RS-485

Quick Start — MSG0804 and MSG0808

Installation

Step 1

Turn off power to the switcher and all other devices that will be connected.

Step 2

To rack mount the switcher, install the included brackets, then mount the switcher. Otherwise, install the four rubber feet (included) and place the switcher on a desktop.

Step 3

Using video inputs 1 through 8, attach RGBHV, RGBS, RGsB, RsGsBs, or component video to the switcher using BNC connectors (see illustration at right).

Step 4

Using audio inputs 1 through 8, attach audio inputs to the switcher with 5-pole captive screw connectors (see illustration below right).

Step 5

Connect up to four (MSG0804), or eight (MSG0808), RGBHV, RGBS, RGsB, RsGsBs, or component video output devices to the switcher using the Video BNC connections (see illustration below right).

Step 6

Connect up to four (MSG0804), or eight (MSG0808) audio output devices to the switcher using 5-pole captive screw connectors (see illustration below right).

Step 7

If the switcher is to be connected to a computer or host controller for remote control, connect the host’s RS-232 cable to a 5-pole captive

screw connector and connect it to the serial port on the switcher. Configure

the serial port for the type of control you will be using (RS-232, RS-422, or RS-485) by setting the dip switch

adjacent to the port. (See the serial port pinout table on page 2-4).

Rx+	Rx+	5	1
Rx-	Rx-	5	1
Tx+	Tx+
Tx-	Tx-
Gnd	Gnd	9	6
		9	6
RS-232/422-485		DB9 Pinout (Female)

5-pole captive screw connector/socket

Rack mounting the MSG0808

		Component, Component,
		RGsB,	RGsB,
RGBHV	RGBS	RsGsBs	RsGsBs
R	R	R	R-Y
G	G	G	Y
B	B	B	B-Y

H	HV	H	H
V	V	V	V
Connecting the MSG0808
Unbalanced Input/Output
R		Tip
OUT		See Caution
OUT		Sleeve (s)
L		See Caution
		Tip
	Balanced Input/Output
R		Tip
R		Ring
OUT		Ring
OUT		Sleeve (s)
L		Ring
L		Tip
		Tip
CAUTION	Connect the sleeve to ground
	(Gnd). Connecting the sleeve to a
	negative (-) terminal will damage
	the audio output circuits.

Image 3

Extron electronic manual Quick Start MSG0804 and MSG0808, Rack mounting the MSG0808, Connecting the MSG0808

Contents

MSG0804 and MSG0808 Matrix Switchers Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité Français Connecting the MSG0808 Quick Start MSG0804 and MSG0808Rack mounting the MSG0808 Operation Quick Start MSG0804 and MSG0808, cont’d Table of Contents Table of Contents, cont’d Introduction One Introduction About the MSG Matrix SwitchersMSG Matrix Switcher Features MSG Matrix Switchers Introduction Flexible Control Options This page intentionally left blank Two Installation Tabletop use InstallationMounting the Switcher MSG Matrix Switchers Installation Video Inputs Video Outputs Rear Panel Connectors RS-485 Half Duplex Connection Installation, cont’d MSG0808 installation example Connecting the MSG0804 and MSG0808 Balanced audio Installation, cont’dAudio input and output Unbalanced audio Connecting the external sync signal Vertical Interval Switching This page intentionally left blank Operation Three Front Panel Features MSG Matrix Switchers OperationOperation Miscellaneous front panel functions Connecting inputs with outputsPreset configurations Front Panel Operation Selecting the switching level audio versions only Reset to factory defaultOperation, cont’d Windows-based Control Program Four Installing the Windows-based ICS100 Control Software Using the SoftwareWindows-based Control Program, Cont’d ICS100 Interface screen MSG switcher controls options Using the control panel Creating a new patch Setting volume levelsAdjusting output volume levels Defining input icons and labels ICS100 Set Output Volume window Adjusting input volume levels Opening the Options menu Setting and using presets Resetting the unit VIS EnableEnable Response Using Terminal Comm This page intentionally left blank Five Remote Control Remote Control Dip Switch SettingsMSG Matrix Switchers Remote Control Host-to-MSG Matrix Switcher Communications Addressing commandsUsing the command table Command Description Remote Control, cont’dCommand Table Set-up commands Blank output Switching commandsVolume commands Switching levels audio models only Mute all outputs Stop volume ramp Change input volume level global Remote Control from a NetworkPreset commands Enabling remote control of the switcher over a network ICS100 Serial Port Server window Instructions for configuring the client remote PC Stopping communications from the server PC Adjusting response timeAdjusting the response time Stopping communication Press this button first CTL120-2 IR Remote Control Remote Control, cont’d AAppendix Specifications Video output SpecificationsVideo Video input Audio input MSG Matrix Switchers Specifications A-3Sync Audio audio models only General Specifications MSG0804 and MSG0808Control/remote switcher MSG Matrix Switchers Specifications Reference Information BAppendix To update the firmware Reference InformationUpdating the Firmware Installing Custom Engraved Nameplates Installing the custom nameplatesMSG Matrix Switchers Reference Information Part Numbers MSG Matrix Switcher part numbersOptional accessories Reference Information, cont’d Extron Part BNC-4 Mini HR Cable Plenum Seventeen Conductor Installation CableAssorted connectors BNC connectors Pre-cut cables This page intentionally left blank FCC Class a Notice Extron’s Warranty Extron Electronics, USA