Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic MTP U R A, MTP U R RS SEQ Installation, cont’d, MTP U R Series Installation

Models: MTP U R RSA SEQ MTP U R A MTP U R RS SEQ

1 32

Download 32 pages 3.09 Kb

Page 16

Installation, cont’d

1.	Remove the feet from the bottom of the MTP, if they are
	installed.
2.	Attach the mounting brackets to the MTP with the machine
	screws provided.
3.	For furniture mounting, hold the MTP with the attached
	brackets against the mounting surface. Mark the bracket
	screw hole locations on the mounting surface.
4.	For furniture mounting, drill 3/32" (2 mm) diameter pilot
	holes, 1/4" (6.3 mm) deep in the mounting surface at the
	marked screw locations.
5.	For furniture mounting, insert #8 wood screws into the four
	pilot holes. Tighten each screw into the mounting surface
	until just less than 1/4" (6 mm) of the screw head protrudes.
6.	For furniture mounting, align the mounting screws with
	the slots in the brackets and place the MTP against the
	surface, with the screws through the bracket slots.
7.	For furniture mounting, slide the MTP slightly forward or
	back, then tighten all four screws to secure the MTP in place.
8.	For projector mounting, secure the MTP to a projector
	mount by inserting the mounting bolt through the
	bracket’s slotted hole.

12MTP U R Series • Installation

Image 16

Extron electronic MTP U R A, MTP U R RS SEQ, MTP U R RSA SEQ manual Installation, cont’d, MTP U R Series Installation

Contents

MTP U R RSA SEQ, MTP U R RS SEQ, MTP U R RS, and MTP U R A User’s GuideRev. B Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch安全须知中文 PrecautionsFCC Class A Notice Page Table of Contents Front Panel Controls and IndicatorsMTPT U R Series Table of Contents About the MTP Universal ReceiversIntroduction About this ManualAbout the MTP Universal Receivers Figure 1 - MTP U R series featuresMTP U R Series Introduction Introduction, cont’d TP cable advantagesTransmission distance 4 MTP U R Series IntroductionReceiver Jumpers Setting JMP1 for RS-232 communicationFigure 3 - Setting jumper 1 to uni-directional MTP U R Series IntroductionTransmitter Jumper Introduction, cont’d6 MTP U R Series Introduction Figure 4 - Inverting sync with jumpers 2 andApplication Diagrams Figure 5 - MTP U R and MTPX switcherFigure 6 - MTP U R and SW4 MTP T 15HD A switcher Figure 7 - MTP U R and Xpoint 450 switcherInstallation Installation8 MTP U R Series Installation Figure 8 - Mounting the MTP on a VersaTools shelf MTP U R Series InstallationFigure 9 - Mounting the MTP on a standard shelf Installation, cont’d 10 MTP U R Series InstallationBack of the rack mounting Figure 10 - Attaching the back of the rack kitMTP U R Series Installation Figure 11 - Typical back of the rack installationsENTER PRESET Use the optional mounting kit MBU 123, furnitureInstallation, cont’d 12 MTP U R Series Installationholes, 1/4 6.3 mm deep in the mounting surface at the until just less than 1/4 6 mm of the screw head protrudesConnections and Settings MTP U R Series InstallationRear panel connectors and features for the MTP U R series of Figure 13 - Receivers’ rear panel featuresInstallation, cont’d 14 MTP U R Series InstallationSee “TP cable termination” to wire the RJ-45 connectors BNC connectors for component Y, R-Y, and B-Y video outputMTP U R Series Installation RS-232 communication. Wire the connector as shown belowFigure 14 - Pin assignments for RS-232 wiring Figure 15 - Audio connector wiringInstallation, cont’d Power supply wiring16 MTP U R Series Installation Figure 16 - Power connector wiringMTP U R Series Installation TP cable terminationFigure 17 - TP cable termination Figure 18 - MTP pin assignmentsInstallation, cont’d Front Panel Controls and Indicators 18 MTP U R Series InstallationFront panel features on the MTP U R receivers are shown below SIGNALMTP U R Series Installation Green, and Blue LEDS D all turn off. Release the buttonPeaking and Level Adjustment Installation, cont’d20 MTP U R Series Installation MTP U R Series Installation Skew Delay CompensationSEQ receiver skew compensation 22 MTP U R Series Installation Installation, cont’dNon-SEQ receivers skew compensation Specifications SpecificationsMTP U R Series Specifications Specifications, cont’d N Specifications are subject to change without notice MTP U R Series SpecificationsGeneral N Protocol is mirrored between the transmitter and the receiverSpecifications, cont’d Part Numbers AccessoriesRJ-45 connector 26 MTP U R Series SpecificationsExtron’s Warranty USA, Canada, South Americaand Central America Asia2008 Extron Electronics. All rights reserved Extron USA - WestExtron USA - East Extron EMEA