Fostex MR16 Starting recording, Playing back the recorded track, Undoing recording undo/redo

MR16 Owner’s Manual (Basic operations)

4)	Set track fader 1 and [MASTER] fader to the		Starting recording
	nominal position (marked by	).

Raising these faders allows you to monitor the input sound. If these faders are not raised, you cannot monitor the sound via headphones.

<Note>: The fader for track 1 is used to ad- just the monitor level. To adjust the record- ing level, use the [TRIM] control of the [IN- PUT A] channel.

5)Press the [RECORD] key once (the key indicator

7)While holding down the [RECORD] key, press the [PLAY] key to start recording.

The guitar is recorded.

8)When recording completes, press the [STOP] key to stop the recorder.

<Note>: We recommend to press the [REC SELECT] key for track 1 to unarm track 1.

starts flashing).

Track 1 (which is record armed) now enters the input monitor mode and "" is shown on the home screen.

Playing back the recorded track

9)Press the [REWIND] key while holding down the [STOP] key to locate the recorder to the beginning of the song.

10)Press the [PLAY] key to start playback.

You can adjust the monitor level using the track 1 fader, as well as the [MASTER] fader and [PHONES VOL] control.

If you are not satisfied with the result, use the undo/redo function to cancel the re- cording and try again.

6)While playing the guitar, adjust the recording level using the [TRIM] control of the [INPUT A] channel.

Adjust the level appropriately so that the PEAK indicator does not light.

Turning the [PHONES VOL] control clockwise raises the headphone monitor level.

The screen shows the input level of track 1, as well as the stereo L and R output levels.

Undoing recording (undo/redo)

If you press the [UNDO/REDO] key after finishing recording, you can return to the condition before the recording started (UNDO operation). Therefore, you can try recording again.

If you press the [UNDO/REDO] key again (after UNDO), the undo operation is canceled and you can return to the condition when the recording finished (REDO operation).

POWER

HALL	PLATE	DELAY	BOUNCE MODE	15/16 > STEREO WAV FILE
		EFFECT		BOUNCE

UNDO/REDO

MENU / ENTER

<Note>: Adjust the [TRIM] control properly so that the PEAK indicator does not light at the loudest part of the guitar sound. If the input level is too high, the PEAK indicator lights and the sound may be distorted or noisy.

<Tip>: When receiving a line level signal, set the [TRIM] control to left ("LINE") to get the appropriate level. When receiving a micro- phone signal, set the [TRIM] control to right ("MIC") to get the appropriate level.

			POWERFUL	NATURAL	BRIGHT	TIMEBASE SELECT	STORE	UNDO/REDO
					MASTERING
	EFFECT SEND
0	10
		AUTO PUNCH	PLAY MODE	A / IN	B / OUT	RHYTHM GUIDE	CONTRAST	DIRECT LOCATE
					LOCATE
	PAN
L	R
VWX8	YZ9	+-_0		DELETE
					REC SELECT	REWIND		F FWD
8	9/10	11/12	13/14	15/16	MASTER

MAX		[UNDO/REDO] key
RECORD STOP	PLAY
LOCATE ABS ZERO	LOCATE REC END
MIN	A-B PLAY

<Notes>: The undo/redo function is available for all kind of recordings, however, if you carry out any of the following operations after making re- cording, you cannot undo the recording.

•Carrying out new recording.

•Carrying out track or part editing.

•Turning off the power.

•Selecting another song or editing the song name.

38