Fostex MR16 owner manual Press the Record key once the key indicator starts flashing

MR16 Owner’s Manual (Basic operations)

<Note>: Track 1 and 9/10 faders are used to adjust the monitor level. To adjust the recording levels, use the [TRIM] controls of the [INPUT A] and [INPUT B] channels.

5)Press the [RECORD] key once (the key indicator starts flashing).

The armed tracks 9/10 now enter the input monitor mode, while "" is shown on the home screen.

Starting recording

9)While holding down the [RECORD] key, press the [PLAY] key to start recording.

The recorder records the keyboard while playing back track 1 (guitar).

10)When recording completes, press the [STOP] key to stop the recorder.

<Note>: We recommend to press the

[REC SELECT] key for tracks 9/10 to unarm tracks 9/10.

Adjusting the recording levels while listening to track 1

6)Press the [PLAY] key to play back the song from the beginning.

Though tracks 9/10 are in the input monitor mode, you can hear the track 1 signal by rotating the [PHONES VOL] control clockwise (while the meter for track 1 shows the playback level).

7)While playing the keyboard, adjust the recording levels using the [TRIM] controls of the [INPUT A] and [INPUT B] channels.

Adjust the levels appropriately so that the PEAK indicators for these input channels do not light.

The home screen shows the playback level of track 1 and the input levels of tracks 9 and 10, as well as the stereo L and R output levels.

<Note>: Adjust each [TRIM] control properly so that the corresponding PEAK indicator does not light at the loudest part of the key- board sound.

<Tip>: When receiving a line level signal, set the [TRIM] control to left ("LINE") to get the appropriate level. When receiving a micro- phone signal, set the [TRIM] control to right ("MIC") to get the appropriate level.

8)After adjusting the recording levels properly, press the [REWIND] key while holding down the [STOP] key to locate the recorder to the beginning of the song.

Playing back the recorded track

11)Press the [REWIND] key while holding down the [STOP] key to locate the recorder to the beginning of the song.

12)Press the [PLAY] key to start playback.

You can adjust the monitor level using the track faders, as well as the [MASTER] fader and [PHONES VOL] control.

<Note>: If you are not satisfied with the re- sult, use the undo/redo function to cancel the recording and try again.

Undoing recording (undo/redo)

If you press the [UNDO/REDO] key after finishing recording, you can return to the condition before the recording started (UNDO operation). Therefore, you can try recording again.

If you press the [UNDO/REDO] key again (after UNDO), the undo operation is canceled and you can return to the condition when the recording finished (REDO operation).

POWER

HALL		PLATE	DELAY		BOUNCE MODE	15/16 > STEREO WAV FILE			UNDO/REDO
				EFFECT		BOUNCE	MENU / ENTER
				POWERFUL	NATURAL	BRIGHT	TIMEBASE SELECT	STORE	UNDO/REDO
						MASTERING
		EFFECT SEND
0	10
			AUTO PUNCH	PLAY MODE	A / IN	B / OUT	RHYTHM GUIDE	CONTRAST DIRECT LOCATE
						LOCATE
		PAN
L	R
VWX8		YZ9	+-_0		DELETE
						REC SELECT	REWIND		F FWD
8		9/10	11/12	13/14	15/16	MASTER			[UNDO/REDO] key
						MAX
							LOCATE ABS ZERO		LOCATE REC END
							RECORD	STOP	PLAY
						MIN			A-B PLAY

<Notes>: The undo/redo function is available for all kind of recordings, however, if you carry out any of the following operations after making re- cording, you cannot undo the recording.

•Carrying out new recording.

•Carrying out track or part editing.

•Turning off the power.

•Selecting another song or editing the song name.

40